Two tractors leave point O at the same time and drive in the directions shown. Tractor A is traveling at a m m constant speed of vA = 15 . Tractor B is traveling at a constant speed of vp = 23 - Hint: 1. Use constant acceleration equations to find time. • VA y VB A B Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value 40 degrees 02 40 degrees a. Determine the velocity of tractor A relative to tractor B, v4, express as a Cartesian vector. b. Determine the magnitude of the velocity of tractor A relative to tractor B, c. How long after leaving point O will the tractors be 600 m apart?

Two tractors leave point O at the same time and drive in the directions shown. Tractor A is traveling at a m m constant speed of vA = 15 . Tractor B is traveling at a constant speed of vp = 23 - Hint: 1. Use constant acceleration equations to find time. • VA y VB A B Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value 40 degrees 02 40 degrees a. Determine the velocity of tractor A relative to tractor B, v4, express as a Cartesian vector. b. Determine the magnitude of the velocity of tractor A relative to tractor B, c. How long after leaving point O will the tractors be 600 m apart?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Read the question carefully and give me right solution with clear calculations
DO THIS TYPEWRITTEN AND COMPLETE FOR UPVOTE
In this calculus proble, a machine design has endpoints of a moveable rod of length 1 meter have coordinates (x,0) and (0,y). The position of the end on the x-axis has a formula given at t is the time in seconds. the formula and this 3 part question is listed ona a separate attachment.
The equation of a moving object is SEE PHOTO, answers A-D
The crank A02 of the following mechanism is rotating at 50 rad/sec in counter clockwise direction. Find the following velocities by creating a velocity diagram in SolidWorks. Submit the SolidWorks file in the below submission link. (All dimensions are in mm) 02A AB BC AC CD BO4 30 50 30 60 100 60 30 В 0204 A 140 02 04 30.00 1) What is the velocity of C? Vc = mm/sec (10 Points) at an angle of degrees (5 Points) 2) What is the velocity of D? và - mm/sec (10 Points) at an angle of degrees (5 Points) 3) What is the velocity of B? Vb = mm/sec (10 Points) at an angle of degrees (5 Points) tre 4) What is the angular velocity of link 3? w3 = ]rad/sec (10 Points) : (5 Points) 5) What is the angular velocity of link 5? w5 = rad/sec (10 Points) * (5 Points)
A particle's position (2.17+4.80+- ○100代)3 is given byso unere tis in seconds and s is in Find the particles position and acceleration zero velocity. meters . at the inatant when the panticle has you may use equation the calculator to mode t Find the noots'
I walk 450 steps at 25 degrees south east. Then 750 steps 72 degrees north of west and lastly 700 steps south of west. What will be my orientation and how many steps should I take to come back to starting point Use the following equations
please show work and units.
Please show steps in detail
Please answer the given question as soon as possible. Thank you very much.
A four-bar mechanism is used to transmit power to slider E. Link AC rotates counterclockwise at 100 rpm. A and B are fixed points. The following linkages are measured in cm: AC=35, AB=70, CD=45, BD=45, DE=40. Find the instantaneous velocity of slider E in cm/s 1.Draw the mechanism in appropriate scale on your paper2. Find the instantaneous linear velocity of C3. Find a point on your paper to draw the velocity polygon and scale the magnitude of the computed linearvelocity4. Use the relative velocity equation for finding the linearvelocity of D; ? = ? + ?? ? ?/?5. Remember that although the magnitudes are unknown, their directions can be identified6. Obtain the magnitudes of the unknown velocities from the velocity polygon7. For Link DE, repeat the process by using ? = ? + ??the line as much as needed8. Remember that E is a SLIDER therefore it can only goin the direction where its movement is not constrained? . Add the vector ? to the head of ? and extend?/? ?/??
make the sketch and mention the dimension and reference line for the attached sketch note :using Autocad version (2021) sketch the figure