Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force Pfor which the tensile stresses in rods AB and BC are equal. Take W=15 kips. 30 in 25 -1.95 in W The magnitude of the force Pis) kips.

Q: Convert to isometric drawing mark point A as the lowest point

A: use a 30-60 triangle to create the isometric  figure ng follow the left, front and top illustration…

Q: Which percentile is typically for designing lower-limit dimensions? - 95th 5th 50th 99th

A:

Q: Using the diagram, determine the maximum diameter for DIA B.

A:

Q: What are the two dimensions that are not placed on the field of a drawing? A zero and a 45 degree…

A: The following things needs to be mentioned on the field of drawing: ◆ The diameter or radius of…

Q: 0.2 m B 0.2 m 1.3 m 0.7 m A P Circular

A:

Q: 76°10' 0.500 DIA 45°00'- 1.125 DIA 1.000 0.875 Find length x in the accompanying figure.

A: Given figure can be redrawn as:

Q: Build the following part and report the volume in units cubed. A = 48 B = 51

A:

Q: 2 ft 2 ft 3 ft A 6 ft

A:

Q: 1

A:

Q: can you help me understand this better. I am going to reproduce this drawing by using Creo. And i…

A: Here's a breakdown of the GD&T symbols used in the image:Datum symbols: A datum is a…

Q: E 12.5 m C А 8 m 5 m

A:

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: Determine the magnitude of F so that the resultant couple moment is 11.5 kN -m , counterclockwise.…

A:

Q: 3 show all steps in detail, units and formulas please.

A:

Q: Circle the letter corresponding to the view on the right that shows the result of rotating the…

A: (1) Find Rotate the object (1) about the z-axis and then about the x-axis.

Q: COMPLETE THE ORTHOGRAPHIC VIEWS FOR EACH OF THE OBJECTS SHOWN BELOW.

A: To find:Orthographic views of each.

Q: 0.50 1.25 3.00 1.00- 2.00 1.00

A: Given,

Q: 8 inch radius 8 inch circumference 8 inch all around 8 inch diameter R.70 4x 1.40 B IP 1.00 SECTION…

A: Select the correct statement about the notation circled in green and marked as letter.C. Assume all…

Q: Q1: Use scale (1:1), draw the front, top & side views of shape shown below. (50 M)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Find y shown in Figure below. 3 cm 0.5 cm - 0.5 cm A 1 cm B 0.5 cm D 6 cm E 0.75 cm F 0.75 cm 0.75…

A: Solution:

Q: SPECIFY WHERE DIMENSIONS NEED TO BE PLACED FOR THE FOLLOWING PART NOTE: JUST NOTE WHERE…

A: To mark the letters on the following figure mentioned.

Q: Partition the given figure and find the x and y coordinates.

A: Task at hand is to find the centroid of the shape in the figure

Q: 1-12.Determine length CE for the similar triangles shown in Figure P1-12. Mind the lengthside E 12.5…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.