Two resistors, R₁ = 47 k and R₂ = 50 k2, a 31.5 mH inductor, and a 47 V battery are used to form the circuit shown above. The switch S was open for a long time. The switch is closed at t = 0 s. a. Immediately after the switch is closed what are... the current through the battery? the rate of change (dI/dt) of the current through the battery? Submit Answer Some items were not submitted. Tries 0/10 Previous Tries b. Same questions as in a. after the switch has been closed for 0.728 us: the current through the battery? the rate of change (dI/dt) of the current through the battery? Submit Answer Tries 0/10 c. A long time has passed since the switch S was closed. What are... the current through the battery? the rate of change (dI/dt) of the current through the battery? Submit Answer Tries 0/10

Two resistors, R₁ = 47 k and R₂ = 50 k2, a 31.5 mH inductor, and a 47 V battery are used to form the circuit shown above. The switch S was open for a long time. The switch is closed at t = 0 s. a. Immediately after the switch is closed what are... the current through the battery? the rate of change (dI/dt) of the current through the battery? Submit Answer Some items were not submitted. Tries 0/10 Previous Tries b. Same questions as in a. after the switch has been closed for 0.728 us: the current through the battery? the rate of change (dI/dt) of the current through the battery? Submit Answer Tries 0/10 c. A long time has passed since the switch S was closed. What are... the current through the battery? the rate of change (dI/dt) of the current through the battery? Submit Answer Tries 0/10

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Related questions

Q: The switch in the R-C circuit shown is initially set to position A which the capacitor charges up.…

A: Given that: V=20 VR1=2 kΩ=2000 ΩR2=5 kΩ=5000ΩC=5μF=5×10-6 F

Q: In the following figures, each conductor carries 2.0 A of current into or out of the page. Draw a…

A: The above problem can be solved by using Ampere's Circuital Law. According to this law

Q: The generator at a large power plant has an output of 1,800,000 W at 30,000 V. a. If it were a DC…

Q: As shown below, a wire loop (that is immersed in a 0.43 T B-field) grows from a radius of 4.2 cm to…

Q: At time t=0, the switch in the circuit shown in the figure is closed. After a sufficiently long…

Q: A 90 mH inductor carries a current that varies with time according to… i(t) = t2+6t (in A with t in…

A: Given that, The inductance of the inductor, L = 90 mH Current, i(t)=t2+6t We need to find the…

Q: The switch in (Figure 1) has been open for a very long time. The switch is closed at tt = 0 s.…

A: Given, emf of the battery, ε = 170 V

Q: The capacitor in the circuit shown below is initially uncharged. The switch is closed at t=0 s.…

A: The voltage of the battery is The capacitance of the capacitor is The resistance of the resistor is…

Q: possible, please write on paper and upload photo of paper. Other forms of answers do not show for…

Q: A square loop of aluminum wire is 17.0 cm on a side. It is to carry 12.2 Aand rotate in a uniform…

Q: a. Consider the current configuration shown below. What is the magnitude of the cur- rent in the…

Q: The motor in a toy car operates on 5.30 V, developing a 3.90 V back emf at normal speed. If it draws…

Q: A wire 2 m long moves perpendicular through a 0.08 I field at a speed of 7 m/s. What EMF is induced?…

A: Given: l=2mB=0.08Tv=7m/sR=0.50ΩUsing:Emf:ξ=BlvI=ξR

Q: A. B. C. D. The current I, in amperes, flowing through an alternating circuit, at a time of t…

A: Given:- Current through the alternating circuit is I=30 sin(bt) Period of the function is T=125 s

Q: The primary coil of a transformer is coupled to DC power supply (a battery) that provides an…

Q: The motor in a toy car operates on 6.00 V, developing a 4.50 V back emf at normal speed. If it draws…

A: Given V = 6.00V Vback = 4.50 V I = 3.20 A R =??? I1 =???..(at start Vback =0 V)

Q: The capacitor in the figure below is uncharged for t < 0. If e m f = 9.42 V, R = 59.4 Ω, and C =…

A: Given, emf,ε=9.42V,Resistance,R=59.4ΩCapacitor,C=2.50μF = 2.5×10-6FExpression be…

Q: A battery with Ɛ = 8.60 V and no internal resistance supplies current to the circuit shown in the…

A: Given: Emf, ε=8.60 V I∘=8.60 mAIa=1.00 mAIb=1.16 mA When the switch is open, Resistances R1,R2,R3…

Q: Consider the circuit shown below. Find I1. 12, andl3 when (a) the switch S is first closed, (b)…

A: When the switch is open , the current through the inductor is zero. Due to transient effect of…

Q: The capacitor in the figure below is uncharged for t < 0. If Ɛ = 9.02 V, R = 58.4 N, and C = 2.50…

Q: The rod shown below moves to the right on essentially zero-resistance rails at a speed of v=2.20…

Q: A battery with E = 3.00 V and no internal resistance supplies current to the circuit shown in the…

Q: Problem 6: In the questions below there are 6 induction processes. The circle with the dot 000000000…

A: According to Lenz's law, the induced electric flows in such a direction that it opposes the change…

Q: In the circuit shown in the figure below, let L = 2.60 H, R = 6.70 2, and E= 120 V. What is the…

A: In an LR circuit, the self-induced emf (εL) is given by: εL=LdIdt=Ɛ-IR where L is the inductance, I…

Q: After the switch is closed the current takes 5ms to reach 80% of its max value. What is the…

A: Solution: Given: LR series circuit is given with DC battery for power. We are required to find the…

Q: During a starter current draw test, the measured current is greater than specified, and the cranking…

A: The cause of higher current than specified and the lower cranking speed and battery voltage. Given…

Q: Consider his circuit, which has C = 0.50 F and L = 0.20 H. With the switch open, the capacitor is…

A: We are given capacitance and inductance. We find the charge on capacitor. The charge on capacitor…

Q: R2 Consider the circuit shown in the figure. Suppose that the switch has been open for a very long…

Q: In the circuit shown in the figure below, let L = 2.20 H, R = 6.80 Ω, and = 120 V. What is the…

Q: Consider a transformer, used to recharge rechargeable flashlight batteries, that has 500 turns in…

Q: In which of the following systems does Ampere's law apply? Consider that a constant total current I…

A: In which of the following system does ampere law apply.

Q: How much forces is needed to accelerate a 1400 kg car 2 m/s2 ? O 2700 N O 2800 N O 2600 N

A: Newton's first law explains a force is required to change the motion of the object. If no force is…

Concept explainers

Voltage Across Inductor

An actor is a passive electrical component that consists of a coil bent in the form of wire which uses electromagnetism to produce electric current through the coil. When the electric current flows through a conductor that is the coil, a magnetic flux is developed around the conductor. This flow of current through the coil creates a magnetic field based on Fleming's Right-hand thumb rule. If there is any decrease in the current passing through the inductor, then the magnetic field will also decrease and energy is released through the generation of electric current. There is also a secondary voltage inducing in the same coil due to the magnetic flux, since it opposes any changes in the electric current flowing through the circuit. An inductor is also called choke, coil, or solenoid. A choke is designed to block certain frequencies when the DC current passes. A winding coil is coated with insulation to give extra insulation and protect the circuit. They are usually tightly wrapped around a central core which is cylindrical in nature so that the magnetic flux can be induced. The solenoid is a three-dimension coil that is used to exhibit electromagnetism when the magnetic field is developed due to the current flowing through the coil. The sign convention of the inductor is the same as the power dissipating device. When the current flows into the positive side of the voltage across the inductor, the value is positive and the inductor dissipates power whereas when the inductor releases the power back to the circuit, the current has a negative sign convention. 

Question

L
S
Two resistors, R₁ = 47 ks and R₂
=
W
R₁
m
a. Immediately after the switch is closed what are...
the current through the battery? |
50 kn, a 31.5 mH inductor, and a 47 V battery are used to form the circuit shown above. The switch S was open for a long time. The switch is closed at t = 0 s.
the rate of change (dI/dt) of the current through the battery?
Submit Answer Some items were not submitted. Tries 0/10 Previous Tries
b. Same questions as in a. after the switch has been closed for 0.728 µs:
the current through the battery?
the rate of change (dI/dt) of the current through the battery?
Submit Answer Tries 0/10
R₂
c. A long time has passed since the switch S was closed. What are...
the current through the battery?
the rate of change (dI/dt) of the current through the battery?
Submit Answer Tries 0/10

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Formula

VIEW

Step 2: When time t=0

VIEW

Step 3: When t= 0.728 µs

VIEW

Step 4: When t =∞

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

Question in the attachment
A Transformer has 400 primary turns and 1800 secondary turns. The input voltage is 24V and the output current is 4A when connected across a load. a. What is the output voltage of the transformer? b. What is the resistance of the load? c. How much power is dissipated by the resistor?
The diagram shows an ideal (zero internal resistance) DC source connected to three identical resitances and a switch. In the diagram, the switch is open. If initially, the switch is open, what happens to current I1 and I2 after the switch is closed? I1 increases, decreases, or stays the same and I2 increases, decreases, or stays the same?
1. An inductor of 4 H and a resistor of 10 ohms are connected to a 20 V battery. The switch connecting all three in a circuit is closed at time t=0. a. What is the initial current in the circuit? b. What is the final steady state current in the circuit? c. What is the initial rate of increase of the current? d. What is the time constant? IS
At t =0s, the current in the circuit in the figure is I(0). At what time is the current (1/2) I(0)?(Figure 1) Express your answer with the appropriate units.
Answer must includecorrect units
A 12.0V battery is connected to a 20.0 Ohm resistor and a 50.0H inductor as shown in the figure below. a) Switch S1 is closed at t = 0 while switch S2 remains open. What is the current in circuit (b) after 1.0s?b) Switch S2 is opened and S2 is closed at t = 10.0s. What is the current through the resistor after 1.0s?
A circuit is set up as the figure below. . (a) Find current I₁ and I2. (b) If the 3 resistor is a heater and is heating a cup of 30 g of water and 10 g of ice that is originally at 0°C. What would be the final temperature of the water after 30 minutes? (c) Draw two arrows at location P to show the direction of magnetic field due to Wirel and Wire2, respectively. 18 V L 4Ω M 202 12 02 P 1₁ AAA 1Ω Wire1 Wire2 3Ω
The generator at a large power plant has an output of 1,800,000 kw at 30,000 v. a. If it were a DC generator, what would be the current in it? b. What is it’s energy output each day in kilowatt hours?
The switch in (Figure 1) has been open for a very long time. The switch is closed at t = 0 s. Assume Ɛ = 190 V. Part A At t = 0 s, what is the current in the 60 SN resistor? Express your answer with the appropriate units. HẢ IGo n = 1.9 A Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining Part B At t = 0 s, what is the current in the 40 N resistor? Express your answer with the appropriate units. HẢ I40 2 = Value Units Submit Request Answer Part C Figure < 1 of 1 At t = 0 s, what is the current in the 10 N resistor? Express your answer with appropriate units. Closes at t= 0s HẢ 60 N 10 N I10 2 = Value Units 40 N 2.0 μF Submit Request Answer
A 60V motor has an ammeter hooked up to it. At motor start up, the reading is BA. A moment later, the reading drops to 2A. What is the back emf of this etectric motor? Select one: a. 30V b. 50V C. 45V d. 180V
With the switch in the circuit of 27.4a closed, there is no current in R2 because the current has an alternate zero-resistance path through the switch. There is current in R1, and this current is measured with the ammeter (a device for measuring current) at the bottom of the circuit. If the switch is opened (27.4b), there is current in R2. What happens to the reading on the ammeter when the switch is opened? (a) The reading goes up. (b) The reading goes down. (c) The reading does not change.