Two resistors, 3 and 5 , are connected in series. The series combination of these resistors is connected in parallel with a third resistor of resistance 8 02. This parallel combination is then connected in series with a fourth resistor of 9 Q resistance. Calculate the total current in the circuit (in Amperes) if 200 V is applied across the combination of the four resistors. Round off to the nearest tenth digit.

Q: What is the voltage across each one of the resistors in Part 1? O Approximately 2.5V, because there…

A: The total resistance of the circuit is: Req=220+220+220+220Req=880Ω So, the current in the circuit…

Q: Determine the voltage across the resistor R1 if the Zener Voltage is 4.7 V * R2 1K R1 5V D2 1K

A: In this question,   We need to determine the voltage across the resistor R1 if the Zener Voltage is…

Q: What is the value of Vab in polar form.

A:

Q: Please, find the total resistance and the current in each component

A: The total resistance of the circuit needs to be calculated and the current through all the…

Q: What is the value of the pair Id and Vo in the circuit in the figure?

A: In this question , we will find output voltage and diode current...

Q: 12V 50 m m 20 375 3105 Solve The following mixed Circuit 1. Intensites of Resistances 2. Vottages of…

A:

Q: V, V2=

A:

Q: Find  Req  for the following circuit.  All value of resister is 11 ohm.

A: The given circuit is redrawn as shown in the figure below.

Q: +5 V +50 V Via R R 47 0 out out 3.3 kn -5 V -50 V

A: Solve the problem

Q: Ohms Law and combinations of resistors. In this figure, what is the voltage at point A?

A: To solve above problem, we will use Ohm's law and Kirchhoff's law: Ohm's law state that in a current…

Q: Three resistance 5each are connected in star. Values of equivalent delta resistances are (b) 2.5 N…

A: we need to find out equivalent delta resistances.

Q: Three equal resistors are connected in series has an equivalent resistance of 3 ohms. What is the…

A: If n equation resistors of resistor R are connected in series than equivalant resistance is R×n. If…

Q: What is the Norton's resistance

A:

Q: 3) When two resistors RA and Rg are connected in series, the total resistance is 360. when connected…

A:

Q: alculate the value two resistan which when connected in series give 50 and 8 when in parallel

A: let two resistors are x and y. So equivalent resistance when connected in parallel is xyx+y and when…

Q: A 1 mA meter D'Arsonval movement with an internal resistance of 100 2 is to be converted into 0-100…

A:

Q: Current through ammeter A2 and A3 in the figure below are 1/100 and 1/700 The reading of ammeter A1…

A: AC network given is, Here, I2=1∠10° A and I3=1∠70° A.

Q: What is the current lo in the figure if Is = 70? Is 2 A

A: Given :  Note : Please note that according to the units of the other currents we have assumed the…

Q: In series combination the current passing through each resistor is Select one: O a. high O b.…

A: In series circuit current flows through all the elements or resistors are equal or same

Q: when would you connect batteries in series compared to connecting batteries in parallel

A: If we want to increase the capacity of the system we should connect the batteries in parallel to…

Q: in step 2 is that 5r

A: here we need to explain the step 2 only

Q: Ibq=30 mikroamper B=99 R2=?

A: As we have given : VCC=15 VR1=10 kΩRC=2 kΩR=1 kΩIB=30 μAβ=99

Q: a. Formulate KVL on input or base loop! b. Calculate and determine IB! c. Calculate and determine…

A: The required parameters can be calculated by using the DC analysis of the amplifier circuit.

Q: what is the Value of the resistance (R) Yesistor is 2:5 レ? 50 R3 181

A: Nodal analysis is a technique to find the currents in any path. Kirchoff's current law (KCL) is used…

Q: The voltage in Figure 1-b is applied to the circuit in Figure 1-a. Accordingly, I and V measuring…

A:

Q: For the circuit to the right, what is value of the voltage v? a 1,57 b) IN c) d) N e) None of the…

A:

Q: R2 560N R1 R3 2200 3300 V1 12V R4 3300 R5 1k0

A:

Q: why is the total parallel resistance less than the smallest resistance

A:

Q: Capacitors C₁ and C₂ are connected in series to the battery as shown. When you close switch S, a…

A: In this question, we need to choose the correct option. Momentary current indicated by which…

Q: Solve the equivalent resistance across: 'b' and 'd' Submit answers in Ohms. 3.0 12 3.0 а 4.0 3.2 3.0…

A: We need to find out equivalent resistance between given point

Q: The value of a shunt resistance required to convert an ammeter of 1 mA with 100 Q internal…

A: we need to find out value of shunt resistance.

Q: A B

A:

Q: In this circuit, R, and Rs are in R2 R1 35 V RA R3 wwww R6 Rs O a. neither series nor parallel Ob.…

A: Series Connection: Elements are said to be in series when elements are connected to a single node…

Q: What is the current lo in the figure if Is = 70? %3D Is 2A 4A

A: All currents at the junction Incoming = outgoing  So use that technique Here 2 and 4 entering  70…

Q: Three resistors of 10, 15 and 20 ohms each are connected in parallel. What is the equivalent…

A: The equivalent resistance can be calculated by using the parallel resistance reduction technique.

Q: Calculate the voltage and current values listed for each of the following series and parallel…

A: Given circuit,

Q: Determine the voltage across the resistor R1 if the Zener Voltage is 5.1V * R2 1K R1 5V D2 1K

A: The given circuit is:

Q: 21. Three resistance 5 each are connected in star. Values of equivalent delta resistances are (a)…

A: we need to find out delta equivalent resistances.

Q: The voltage across each resistor in a parallel connected resistor circuit is O a. Neither same nor…

A: Let R1 and R2 are two resistances connected across a supply voltage V. By using Current division…

Q: A counter circuit is shown in the figure. The counter counts as QO Q1 Clock K 2aQo0100-01-- 10--11--…

A: A counter circuit is shown in the figure.  Find the counter sequence?

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.