Two pulleys with diameter 500 mm and 1200 mm are connected by crossed belt drive. If the belt transmits 20 hp and the distance between the shafts is 4 m, which of the following is the angle of contact between the belt and the pulley? Group of answer choices 0.3 rad 2.8 rad 0.4 rad 3.5 rad

Q: Q1: A rotating shaft carries four masses A, B, C, and D radially attached to it. The centers of mass…

A:

Q: Part (f) Determine the torque applied on the bolt by F4 in terms of the variables and angles given…

A:

Q: 350 mm 600 mm 400 mm 600 mm. 550 mm 400 mm 450 mm 1600 N A) Draw a free body diagram of the Rod. B)…

A: Find the tension in the cables and reaction at the joint

Q: A multi-rod mechanism is used to move paper rolls over the transmission line. Get a degree of…

A: Solution : It is a basic four-bar chain with four turning pairs. The degree of freedom is calculated…

Q: Q4: Determine the plate thickness if the rivet diameter was 10 mm?

A:

Q: FD Fc FB F.

A: Four forces, FA, FB, FC, and FD, each of magnitude 1 N, are applied to a square object at the points…

Q: The steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100…

A:

Q: A motor (located at C) provides 50kW of power which is then used by pulleys A and B. When the motor…

A: GivenPC=50kWPB=30kWPA=20kWN=200 rpmd=5cm

Q: Find the force generated by the deltoid (right arm) if: His arm length (d) is: 0.84 m The COG of the…

A: Arm Length d=0.84mCOG=37%Wa=7.9NWw=126NAngle=90°Insertion=0.17mAngle for line of pull=11°…

Q: 2 of 5 Review The cable is tied to the top of the ol rig, wraps around the lower pulley, then around…

A:

Q: What is the power output of a motor that provides a torque of 2,917 N*m while running at 2,641 rpm?…

A: The objective of this question is to calculate the power output of a motor given the torque and…

Q: 3. Draw a FBD that would enable you to calculate the force T' in the muscle. ● 2 55° 6" 5 lb G 13" A…

A: To draw the FBD for the given loading.

Q: Question 4 ) Listen AV-belt is wrapped around a Ø5.00-inch pulley with a 38.0° groove angle.…

A: Given data-angle in degree for belt wrap=38.0°C

Q: 1. A moving company rigs a pulley system to lift a piano to a fourth floor balcony 44 feet from the…

A: Write the given data. Number of supporting pulley, ns=6Number of down pulley, nd=1Wpiano=1200…

Q: You are trying to move a light fixture into an apartment. There are hooks in the elevator so you…

A:

Q: (c) As a combat engineer serving in the battlefield, you were assigned by your captain to rapidly…

A: Weight of an object is defined as mass times the acceleration due to gravity. Weight of an object…

Q: As shown in Figure 3, Block A has a mass of 12 kg and is resting on a horizontal surface. Block B…

A:

Q: fluid is displaced to the slave cylinder which is 20 mm in diame slave cylinder on the clutch is 850…

A: 2,5:1Dm=15mmDs=20mmFs=850NFoot pedal moves=70mm To-Find:- a Force applied to the foot pedalb…

Q: Find the forces developed at pins E. 4 kN/m

A: Given

Q: In the motion on inclined plane, the frictional force is directly proportional to reaction force…

A:

Q: 2L Answer: DI = B 4 m 2L i 3L D 4 m m 2L E H 2L AB=BC=CD=DE = EF = FG L F 4 m

A:

Q: /0.009MA BM FOLE 4. Answer:

A: Geometric Dimensioning and Tolerancing (GD&T) could be a language of symbols and measures…

Q: Find the spring constant if a 20. N force stretches a spring 2.0 m.

A: Given data : Force F=20 N Extension X=2 m   To find : Spring constant

Q: Boom AC is pin-connected at A and supported by a cable attached at C. For the given load, applied at…

A:

Q: Find the spring constant if a 20. N force stretches a spring 2.0 m.

A: GivenF=20N∆=2m

Q: A 200 m tape weighing 35 N is suspended between the two ends under a standard pull of 176 N. The…

A:

Q: flat belt is wrapped around a Ø2.00-inch pulley for 220°.Calculate the belt wrap in radians.

A: The angle of wrapped around a pulley,(θ)=220o Diameter of the pulley, (d) =2 in. Calculate the belt…

Q: A 1000 Ibs TTTTT t A horizontal cable exerts a force of 399.971 pounds while holding a boom into…

A:

Q: 0.75 in. 1'in. -20° 1.5 in.1 in. 3 in. 5 lb D 5 lb

A: Given,

Q: Solve correctly Draw FBD

A:

Q: 1. Four pulleys are attached to the 55 mm diameter steel shaft. If torques is applied to the pulleys…

A: Given data: The diameter of the shaft, d=55 mm. Refer to the table "properties of steel: to the…

Q: 158 158 258 350 The crate weight is 270 lb. The minimum force p for tipping is lb

A:

Q: Compute the moment about point D.

A: Given data: F1=50 lbF2=150 lbM=500 lb.ft Need to determine the moment about the point D.

Q: The boom has a negligible weight, but has sufficient strength to support the 1000N load. Find the…

A:

Q: A pulley system is combined with an inclined plane. The pulley system has an IMA of 3, an efficiency…

A: Given data: IMA = 3 The efficiency of the pulley system, ηpulley=96% weight of the box, W = 215 lb…

Q: 27. A cylinder is required to move a 4200 lb load 20 inches in 2 sec- onds. What is the output…

A: Given : force = 4200 lb distance = 20 inches time = 2 sec   velocity = distance/time  = (20/2) = 10…

Q: A shaft transmits (7.5 x ) kW of power at a speed of 150 rev/min. The torque on the shaft is: O a.…

A:

Q: The inner diameter of the shaft is 180 mm and the diameter ratio is 1.2.  Find the polar modulus of…

A:

Q: Problem 1: Calculate the forces in the required members of the truss shown: F1 F2 F3 H F h F4 D E C…

A:

Q: Use Method of Sections to find the forces in members CF & CD.

A: Given data Given truss system

Q: Two pulleys are used to transmit power between two shafts 1.95 m apart and connected by a parallel…

A:

Q: 600 lb FOR -6 ft -6 ft 7200 lb-ft 12 ft 150 lb/ft B

A:

Q: tage of 2,5:1 acts on the master cylinder which is 15 mm in diameter. Hydraulic  fluid is displaced…

A: Dm=15mmDs=20mm Fs=850NP=70mm To-Find:- 1) The force which must be applied to the foot pedal2) The…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.