Two pulleys, one with radius 8 inches and one with radius 4 inches are connected by a belt, sothat they have the same linear speed. The 4 inch pulley begins rotating at an angular speed of 2revolutions per minute.Compute the linear speed of the 8 inch pulley.The 4 inch pulley and 8 inch pulley are connected, and so will have the same linear speed.Compute the angular speed of the 8 inch pulley. Give your answer in each of the followingforms:• radians per minutedegrees per minute• revolutions per minute

The radius of the first pulley r1=8 inches The radius of the second pulley r2=4 inches The angular…

Answered: Two pulleys, one with radius 8 inches…

Similar questions

An engine flywheel initially rotates counterclockwise at 6.83 rotations/s. Then, during 25.1 s, its rotation rate changes to 2.19 rotations/s clockwise. Find the flywheel's average angular acceleration (including its sign) in radians per second squared. Define counterclockwise rotation as positive. what is the average angular acceleration?
Please Asap
Please answer C, D, E The angular position of a rod varies as 20.7t2 radians from time t = 0. The rod has two beads on it as shown in the following figure, one at r1 = 13 cm from the rotation axis and the other at r2 = 32 cm from the rotation axis. (Note: figure may not be drawn to scale.) (a) What is the instantaneous angular velocity (in rad/s) of the rod at t = 3 s? (Indicate the direction with the sign of your answer. Round your answer to at least one decimal place.) 1.24.2 rad/s, ANSWERED (b) What is the angular acceleration (in rad/s2) of the rod at t = 3 s? (Indicate the direction with the sign of your answer.) 41.4 rad/s2, ANSWERED (c) What are the tangential speeds of the beads (in m/s) at t = 3 s? vt, 1 =16.146 m/s, ANSWERED vt, 2 =____m/s (d)What are the tangential accelerations of the beads at t = 3 s? (Enter the magnitudes in m/s2.) at, 1 = ______ m/s2 at, 2 = ______ m/s2 (e) What are the centripetal accelerations of the beads at t = 3 s? (Enter the magnitudes…
The answer is supposed to be v=2.56m/s but I'm not sure how to write out the problem.
The tolerance is -+1 in the 3rd significant digit
Computation M t = An electric grinder is switched on at t = 0, accelerates uniformly for 17 s to its operating angular speed of 34 rad/s. The wheel then turns at constant angular speed for 34 s and is switched off, slowing uniformly at 9.3 rad/s² until it stops. From the time it is switched off, how long does the grinder take to stop turning? S QL Record your numerical answer below, assuming three significant figures. Remember to include a "-" as necessary.
A propeller is modeled as five identical uniform rods extending radially from its axis. The length and mass of each rod are 0.829 m and 2.71 kg, respectively. When the propellor rotates at 589 rpm (revolutions per minute), what is its rotational kinetic energy ??
A person pushes on a lever 0.7 meters away from the axis of rotation with 100 N of force. The rotational inertia of the lever is 35 kg*m2. Calculate the angular acceleration of the lever.
A clay cylinder of radius 21 cm on a potter's wheel spins at a constant rate of 15 rev/s. The potter applies a normal force of 15.3 N to the clay with his hands where the coefficient of friction is 0.1 between his hands and the clay. What is the power (in W) that the potter has to deliver to the wheel to keep it rotating at this constant rate?
Please answer this within 30 mins ! I will upvote !
A wheel of radius 0.447 m is mounted on a frictionless horizontal axis. The rotational inertia of the wheel about the axis is 0.0458 kg-m2. A massless cord wrapped around the wheel is attached to a 3.00 kg block that slides on a horizontal frictionless surface. If a horizontal force of magnitude P = 2.91 N is applied to the block as shown in the figure, what is the angular acceleration of the wheel? Take the clockwise direction to be the negative direction and assume the string does not slip on the wheel.
Please help me understand the concepts to work this practice problem out.

SEE MORE QUESTIONS