Two parallel shafts are to be connected by Spur gearing. The approximate distance between the shafts is 600 mm. If one shaft runs at 120 rpm and the other at 360 rpm, find the number of tech on each wheel, if the module is 8 mm. Also determine the exact distance apart of the two shafts.

Q: A follower plate B holds a pair of 26-tooth planet gears C against a 20-tooth sun gear A. Each plan…

A:

Q: The drawing represents a planetary reduction gear used in aeronautics. Calculate the speed of the…

A: Speed of motor: N3=1200 rpm and considering N1=0 (is fixed) Number of teeth: Z1=50 teethZ2=18…

Q: A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth.…

A:

Q: 1 to one module.

A:

Q: 2. Shafts A and B are connected by rolling cones and are turning in the same direction. A makes…

A: A shaft is a spinning machine element with a circular cross-section that is used to convey power…

Q: For the following differential gear, if the number of teeth is as follows: N = 24, N2 = 48, Na = 18,…

A:

Q: The lath machine in the ( mechanical workshop uses epicyclic gear train snuwn in Figure 1 to…

A: given data; ⇒pitch circle dialmeter (d) of gear  D=214mm⇒module (m)=4mm⇒speed of arm(y)=1…

Q: A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4 wheels of the…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: A two-step power transmission with two identical gear sets (pinions and output gears) is designed to…

A:

Q: Two mating spur gears have 40 and 120 teeth respectively. The pinion rotates at 1200 rpm and…

A: Given :- Two spur gear of Z1=40 teeth and Z2=120 teeth  Pinion rotates at N1=1200 rpm  Torque is…

Q: Department of Mechanical Engineering are task n a hoist equipment using a reverted epicyclic gear…

A:

Q: In order to test the efficiency of reducer gear train 1 kW input was given at the input end at a…

A: Given:Torque, T=56.36 N-mInput power, P=1 kW or 1000 WInput end speed=1440 rpmspeed reduction=10:1

Q: In a single-stage gear wheel system with an evolvent profile, the rotating (drive The number of…

A: to prevent undercutting, we need to increase the pressure angle or the helix angle.

Q: The lathe machine in the Central University of Technology mechanical workshop uses epicyclic gear…

A:

Q: rpm of D in the clockwise direction is

A: Figure shows the epicyclic gear train.For this data is given as: Number of teeth on the gears;…

Q: The gear train has the following properties: Gear 2: N2 = 14 teeth and Pd = 14 Gear 3: d3 = 2.0 in.…

A:

Q: 7. A typical drive train for a 'geared' bicycle meant to be used on paved road (see a representative…

A: (a) Write the given data. Tf=48Df=10.5 inTs1=30Ts2=26Ts3=23Ts4=20Ts5=16Ts6=12Nf=105 rpmFf=28 lb

Q: Question 1 A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4…

A:

Q: A rolling cone with a center angle of 15° turning at 240 rpm makes external contact with the second…

A: Given data: The Center angle of the first rolling cone is 2α=15°, The revolution of the first…

Q: belt is on the steps either side of the center step. If the minimum speed is 40 rpm and the smallest…

A:

Q: An epicyclic gear shown in Figure 1 consists of ring gear, planet gear and sun gear. The ring gear…

A: Given Data Ts=32 teeth Tr=72 teeth Arm y=20 rpm

Q: A straight tooth spur pinion has a 19 tooth pinion rotating at a speed of 1640 rpm. The driven gear…

A:

Q: An epicyclic gear in figure 1 consists of ring gear, planet gear and sun gear. The ring gear has 72…

A: Given Data Ts=32 TR=72 Y=+20

Q: Draw the figure and show your solutions. PLEASE ANSWER IT ASAP FOR AN UPVOTE.   Shafts A and B are…

A:

Q: Each of two gears in a mesh has 60 teeth and a module of 6 mm. The teeth are of involute profile.…

A: Data given-  T = 60  m = 6 mm  Arc of contact = 2.5 × circular pitch

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

A:

Q: Two shafts A and B are connected by rolling cones and turn in the same direction. A makes 250 RPM…

A: Given:- RPM of shaft A, NA=250 RPM of shaft B, NB=90 Shaft angle=30 degrees To find:- Cone angle for…

Q: An epicyclic gear shown in figure below consists of ring gear, planet gear and sun gear. The ring…

A:

Q: i need the answer quickly

A:

Q: lb pair of bevel gears having 20 and 75 teeth are used on axes that intersect at a 90" angle.…

A:

Q: The gear ratio shown must transmit 10 horsepower (66000 lb in/s) from its input, which is rotating…

A: For the solution refer below images.

Q: The diagram below shows a shaft with spur gear (B), bevel gear(D), and two supporting bearings (A…

A: Given : The radius is The pressure angle  for the spur gear is The pressure angle of bevel gear at D…

Q: In order to change the direction of rotation a planetary gear is fitted with a compound planet gear…

A: Given data, The gears 3 and 4 is compound gear. Power of the motor, P = 5 kW = 5000 W No of teeth of…

Q: number of pe f the pinion

A:

Q: Find the greatest and smallest values of the velocity ratio of two shafts joined with a universal…

A: Given data :-Universal coupling axis angle = 60°Find out :-(1) Greatest and smallest values of the…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.