Two members, each consisting of straight and 168-mm radius quarter-circle, are connected as shown and support a 500-N load at D. Draw the FBD of the entire frame and members ABC and DBC, including dimensions. Determine the forces in member ABC. Also, calculate the force exerted by member DBC on pin C. 168 mm 168 mm A. B D. 100'mm 500NV 54 mm 252 mm- -324 mm

Two members, each consisting of straight and 168-mm radius quarter-circle, are connected as shown and support a 500-N load at D. Draw the FBD of the entire frame and members ABC and DBC, including dimensions. Determine the forces in member ABC. Also, calculate the force exerted by member DBC on pin C. 168 mm 168 mm A. B D. 100'mm 500NV 54 mm 252 mm- -324 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

y = EI 1 B For the beam and loading shown, determine Part 1 out of 3 (a) the equation of the elastic curve for portion AB of the beam, WO 2 L x Wo -L/2- 1 120 10 X X 1
12 - In the plane truss system, the loading status of which is evident in the figure, the support reactions and all rod forces will be found. A is the fixed joint and B is the sliding joint. Single upload P = 35 kN, dimensions a = 1 m and bar numbers are given. Based on this, which of the following is true? A) The S2 bar is the draw bar.B) NoneC) S3 and S4 bar are pressure bars.D) S1 and S2 bars are pressure bars.E) The S4 bar is the draw bar.
The rigid bars AB and CD are supported by pins at A and D. The vertical rods are made of aluminum and 1 bronze. Determine the vertical displacement of the point where the force P = 10 kips is applied. Neglect the weights of the members. Aluminum L-3t A-0.75 in,2 E-10x 10 psi 3 ft Beonze L-4 A-0.25 in E-12 x 10 psi -2 ft-2 ft-
Each of the links AB and CD is made of steel (E = 29 x 106 psi) and has a uniform 1 rectangular cross section of x 1 in. Determine the largest load which can be suspended from 4 point E if the deflection of E is not to exceed 0.02 in. 8 in. A 8 in. B O A 10 in. D 17 in. E
Determine the force in Pin C for the frame shown. Frame comprises three members - AC, AB, and BD. Lengths are in meters. A B C D 20 40 N 12
8m A 6M using in F B с 100KN 8m 6m Method of Sections determine forces FE, FC, BC
calcualte the forces in members PQ and QR. USE sections method.
Mechanics. help asap pls
A rigid ban AB and "CD" as shown are supported by pins at "A" & "C" and two ross. Determine the maximum force 'p' that can be applied as given if it's vertical movement is limited to 5 mm. Neglect the weight of all the members. www A 3m 3m Aluminium P L = 2m, A= 500m² E =70 GPA 3m IB 3m Steel L=2m A= 300m² E = 2006/ D
500 mm 500 mm B E A -120 N -300- mm PA D 300 mm 750 mm 200 N C For the frame shown below, calculate: a) the magnitude of the force that the pin at C exerts on the member BDC. b) the magnitudes of the forces that the pin at B exerts on the members BFA and BDC. Assume that the 120 N force is applied to the Pin at B.
Determine the forces in members CD, CJ, and DJ.
The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thickness shown in the figure. The working stresses are 70MPa for shear in the rivets and 140MPa for bearing stress due to the rivets. How many 22mm diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE? 000 4 m B с 96 kN D 6 m E 200 KN 4 m F G 4 m 96 kN H to- PBC - -14-mm-thick gusset plate -13-mm-thick angle 6-mm-thick angle PBE