Answered: Two masses are connected as shown. M1…

Two masses are connected as shown. M1 is released and falls 4 m. M2 will cross a friction surface that is 2 m long. Use work-energy to determine the velocity of the mass 1 when it hits the floor?

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter8: Potential Energy And Conservation Of Energy

Section: Chapter Questions

Problem 51P: (a) Sketch a graph of the potential energy function U(x)=kx2/2+Aex2 where k , A, and are constants....

See similar textbooks

Related questions

Q: A rope pulley system with 3 pulleys in the top and 2 in the bottom is required to lift a load. If…

A: Calculate the useful effort.

Q: A uniform plank is supported by two equal 120-N forces at X and Y, as shown. The support at X is…

A: AnswerGiven that, A uniform plank is supported by two equal 120N forces at…

Q: 13 A belt fits tightly around two pulleys of radii 4 cm and 6 cm respectively. The distance betw…

Q: In (Figure 1), an 86 kg construction worker sits down 2.5 m from the end of a 1450 kg steel beam to…

Q: A pin-connected system of levers and bars is used as a toggle for a press as shown in Fig. the force…

A: Given: A pin-connected system of levers and bars is used as a toggle for a press as shown in…

Q: Draw the FBD of the problem A boat exerts a pull of 4000 N on its hawser which is wrapped about a…

Q: A 98N force is needed to push a 45kg box across the wooden floor. What is the value of the…

Q: wi the shope ř(t)= whee ost 2T and SCxy,z)= 2 gr/cm. Find the mass of a. f a conical helix %3D

A: Given : r(t)=<t cost, t sint, t> where: 0≤t≤2π Where, x(t) = t cost…

Q: Answer: T0.005@ A PERPENDICULARITY 8. Answer:

A: Perpendicularity within a 0.005 tolerance zone at MMC relative to datum A

Q: Figure 4 100 g 7. Place a clamp with a hanging mass of 300 g at the 30.0 cm mark of the half-meter…

Q: If a mass of 23 kg acts downward 0.3 m from the axis of rotation on one end of a board and another…

A: Given information: Mass m=23 kg. Distance of mass from the axis of rotation r2=0.3 m. Force F=82.5…

Q: Two boxes ma=11.8 kg and mb are connected by a light string that passes over a frictionless pulley…

Q: 18. A mass (6.73 kg) is 3.20 m above the ground as shown on the left. It has a speed of 4.36 m/s…

A: Given, Mass = 6.73 kg Speed V 1 = 4.36 m/s Height h = 3.2 m Speed V 2 = 6.98 m/s

Q: The two masses (m1 = 5.1kg and m2 = 2.9kg) in the Atwood's machine shown in the figure are released…

A: Given: Mass m1 = 5.1 kg. Mass m2 = 2.9 kg h1 is = 0.77 m The speed of m1 is v1=1.7 m.s-1 Let the…

Q: Scalar is to vector as 1. Speed is to velocity 2. Displacement is to distance 3. Displacement is…

A: The scalar quantities are the one which is having magnitude only. The vector quantities are the ones…

Q: An object weighs 432 N on the surface of the earth. The earth has radius R. If the object is raised…

Q: An aluminum cube with a mass of 22 g sits on top of a block of wood with a mass of 57 g. The block…

A: The second law of motion states that the rate of change of momentum of a body is equal to the force…

Q: A small, rigid object carries positive and negative 3.00 nC charges. It is oriented so that the…

A: Given: Charge, q=3.00 nC r+=-1.20 mm,1.00 mmr-=1.90 mm,-1.30 mm Dipole moment is given in part a;…

Q: Two forces have the same magnitude F. What is the angle between the two vectors if their sum has a…

A: Resultant of two vectors R = (A2 + B2 + 2AB Cosθ )1/2

Q: Using a screwdriver, you try to remove a screw from a piece of furniture, but can't get it to turn.…

A: Given : A man wants to open screwdriver.

Q: The beam and the cable (with a frictionless pulley at D) support an 80 kg load at C. In a FBD of…

A: In a free body diagram, we represent all the forces acting on the body. In this case, the forces…

Concept explainers

Torque

Torque is the rotational equivalent of linear force in physics and mechanics. Based on the course of study, it is also known as the moment of force, rotational force, or turning effect.

Question

mass of pulley = 0

M2 = 5 kg
uk = 0.1
D = 2 m
M1 = 10 kg
H = 4 m
Two masses are connected as shown. M1 is released and falls 4 m. M2 will cross a
friction surface that is 2 m long.
Use work-energy to determine the velocity of the mass 1 when it hits the floor?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

(a) Sketch a graph of the potential energy function U(x)=kx2/2+Aex2 where k , A, and are constants. (b) What is the force corresponding to this potential energy? (c) Suppose a particle of mass in moving with this potential energy has a velocity v when its position is x = . Show that the particle does not pass 2+2 through the origin unless Amv2=k22(1e a 2 ) .
A small block of mass m = 200 g is released from rest at point along the horizontal diameter on the inside of a frictionless, hemispherical bowl of radius R = 30.0 cm (Fig. P8.43). Calculate (a) the gravitational potential energy of the block-Earth system when the block is at point relative to point . (b) the kinetic energy of the block at point . (c) its speed at point B, and (d) its kinetic energy and the potential energy when the block is at point . Figure P8.43 Problems 43 and 44.
The Crab Nebula (see Figure 7.41) pulsar is the remnant of a supernova that occurred in A.D. 1054. Using data from Table 7.3, calculate the approximate factor by which the power output of this astronomical object has declined since its explosion.
A small block of mass m = 200 g is released from rest at point along the horizontal diameter on the inside of a frictionless, hemispherical bowl of radius R = 30.0 cm (Fig. P7.45). Calculate (a) the gravitational potential energy of the block-Earth system when the block is at point relative to point . (b) the kinetic energy of the block at point , (c) its speed at point , and (d) its kinetic energy and the potential energy when the block is at point . Figure P7.45 Problems 45 and 46.
A 3.00-kg object has a velocity (6.00i1.00j)m/s. (a) What is its kinetic energy at this moment? (b) What is the net work done on the object if its velocity changes to (8.00i+4.00j)m/s. (Note: From the definition of the dot product, v2=vv.)
Answer yes or no to each of the following questions. (a) Can an objectEarth system have kinetic energy and not gravitational potential energy? (b) Can it have gravitational potential energy and not kinetic energy? (c) Can it have both types of energy at the same moment? (d) Can it have neither?
A block of mass 0.500 kg is pushed against a horizon-tal spring of negligible mass until the spring is compressed a distance x (Fig. P8.65). The force constant of the spring is 450 N/m. When it is released, the block travels along a frictionless, horizontal surface to point , the bottom of a vertical circular track of radius R = 1.00 m, and continues to move up the track. The blocks speed at the bottom of the track is v = 12.0 m/s, and the block experiences an average friction force of 7.00 N while sliding up the track. (a) What is x? (b) If the block were to reach the top of the track, what would be its speed at that point? (c) Does the block actually reach the top of the track, or does it fall off before reaching the top?
Bullet 2 has twice the mass of bullet 1. Both are fired so that they have the same speed. If the kinetic energy of bullet 1 is K, is the kinetic energy of bullet 2 (a) 0.25K, (b) 0.5K, (c) 0.71K. (d) K, or (e) 2K?
A block is placed on top of a vertical spring, and the spring compresses. Figure P8.24 depicts a moment in time when the spring is compressed by an amount h. a. To calculate the change in the gravitational and elastic potential energies, what must be included in the system? b. Find an expression for the change in the systems potential energy in terms of the parameters shown in Figure P8.24. c. If m = 0.865 kg and k = 125 N/m, find the change in the systems potential energy when the blocks displacement is h = 0.0650 m, relative to its initial position. FIGURE P8.24
A particle is subject to a force Fx that varies with position as shown in Figure P7.9. Find the work done by the force on the particle as it moves (a) from x = 0 to x = 5.00 m, (b) from x = 5.00 m to x = 10.0 m, and (c) from x = 10.0 m to x = 15.0 m. (d) What is the total work done by the force over the distance x = 0 to x = 15.0 m?
A block of mass m = 5.00 kg is released from point and slides on the frictionless track shown in Figure P8.3. Determine (a) the blocks speed at points and and (b) the net work done by the gravitational force on the block as it moves from point to point . Figure P8.3
A jack-in-the-box is actually a system that consists of an object attached to the top of a vertical spring (Fig. P8.50). a. Sketch the energy graph for the potential energy and the total energy of the springobject system as a function of compression distance x from x = xmax to x = 0, where xmax is the maximum amount of compression of the spring. Ignore the change in gravitational potential energy. b. Sketch the kinetic energy of the system between these points the two distances in part (a)on the same graph (using a different color). FIGURE P8.50 Problems 50 and 79