Two loads connected in parallel draw a total of 2.4 kW at a power factor of 0.82 lagging with the first load drawing 1.5 kW at a power factor of 0.70 lagging. If the loads are fed with a voltage of 120 Vrms at a frequency of 60 Hz, the capacitor value needed to increase the power factor of the combined loads to 0.980 lagging is closest to...

Two loads connected in parallel draw a total of 2.4 kW at a power factor of 0.82 lagging with the first load drawing 1.5 kW at a power factor of 0.70 lagging. If the loads are fed with a voltage of 120 Vrms at a frequency of 60 Hz, the capacitor value needed to increase the power factor of the combined loads to 0.980 lagging is closest to...

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A load has a leading power factor. a) Is it a capacitive or inductive load? b) Is the reactive power positive or negative? c) Repeat for a load with lagging power factor
For the circuit shown in the below figure, the value of capacitor 'C such that the power factor will be unity is 230 V, 50 Hz z = 30240°
Load 1 Load 2 24 kW 40 kW pf = 0.8 lagging pf = 0.95 lagging %3D A 240-Vrms, 60 Hz source supplies two loads as shown above. Find the capacitance of a capacitor connected in parallel that will raise the power factor to unity. O 3.14 millifarad O 4.45 millifarad O 1.43 millifarad 5.74 millifarad
Two loads are connected in parallel to a 1000 v(rms) 60Hz source. One of the loads has an average power of 500 kW and a forward power factor of 0.9. Since the other load absorbs 400kw and 600kvar power a) Draw the equivalent circuit of the system b) Find the common power factor of the system c) Find the value of the capacitor to be connected parallel to the loads so that the power factor is 0.95 back d) Find and compare the magnitude of the current drawn from the .source for the situations before and after the capacitor is connected not: Please solve this question in detail, in a way that I can understand
An impedance coil, in series with a resistor takes a current of 3A when connected to a 120V AC source. Using a voltmeter, the voltage across the coil was found out equal to 90V and that across the resistor equal to 30V. Find the power factor of the impedance coil only. The frequency is 60 Hz
Problem 1 • A sinusoidal source with frequency of 60 Hz and rms-voltage of 100 V is connected to an RL load of 10 ohms and 100 uH. Find Power Factor From Calculation Find Power Factor From Plot L=10mH find power factor from calculation only
Three identical Y-connected loads, each having a resistance of 20 22 in parallel with an inductor, are connected to a three phase supply of 400 V and 50 Hz frequency. The power absorb by the load is 8 kW and power factor at the load is 0.9919. (i) Determine the current that flows through the inductor. Please state the assumptions used to solve the question. Calculate load inductance in Henry (H).
find The average power delivered to * .the circuit الحل بطريقة الممانعات وشكرا
For a source which has load has the following characteristics: • Vrms = 125 20° V • P= 400 W • pf = 0.925 lagging What is the rms current and reactive power?
Īs L₁ ~ Load 1: 200 W, unity power factor Load 2: 1200 W at 0.85 power factor lagging Load 3: 400 W + j100 VAR Load 4: -200 VAR । [+ L₂ L3 L4
A load connected to a 210 V rms 50 Hz power lineIt draws 7 kW of power with a back power factor of 0.7.To make the power factor 0.8What should be the value of the capacitor to be connected parallel to the load?
An impedance oil takes 144 watts at a lagging factor of 0.6. What values of capacitance and resistance should be connected in series with the coil if the power input to the latter is to remain unchanged and the overall circuit is to be unity? The circuit is energized by a Voltage of 120 v and frequency is 60Hz