Two individuals are attempting to relocate a sofa by applying forces in the indicated directions. If F₁-540 N and F2- N, determine the vector expression for the resultant R of the two forces. Then determine the magnitude R of the result and the angle which it makes with the positive x-axis (measured counterclockwise from the x-axis).

Two individuals are attempting to relocate a sofa by applying forces in the indicated directions. If F₁-540 N and F2- N, determine the vector expression for the resultant R of the two forces. Then determine the magnitude R of the result and the angle which it makes with the positive x-axis (measured counterclockwise from the x-axis).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam below (EI constant) use the SLOPE DEFLECTION METHOD to answer the following questions. a) How many unconstrained degrees of freedom (DOF) are present in this problem? What are they? b) Calculate the fixed end moments? What is the purpose of a fixed end moments? c) Write the end moment equations in terms of the unconstrained DOF(s). Apply equilibrium to solve for the unconstrained DOF(s). Determine the end moments at A, B and C.
In the structure shown, the support at A rotates 3x10-3 radians CCW, and the support at C has a settlement of 0.8 inches. Make the shear force and bending moment diagram using 1. Three-moment equation 2. Slope Deflection Method Make sure the diagrams for both methods are the same.
The circular shaft AB consists of a 24.2 mm diameter solid steel cylinder in which a 11.4 mm diameter hole has been drilled from end B up to point C. The shaft is attached to fixed supports at each end, and a 150 Nm torque is applied at C. The torque reaction at A is 53.0 Nm. What is the internal torque in segment AC of the shaft? Input your answer as a value only in Nm to one decimal place without +/-sign. L₁ L₂ A 150 Nm B
A brass disk of radius 0.7 ftft and weight 459 lblb sits in a right-angle groove made of granite. The disk makes contact with the groove at AA and BB and the coefficient of static friction at both points are μS=μS= 0.39 A couple moment of MM is applied to the disk as shown.
Beam AC is in equilibrium with loading 100 N at B shown in the figure when β = 45. Determine the unknown forces Ax and Ay at A in x and y direction and Rc perpendicular to the beam AC in y’ direction at C by using the equilibrium equations: ∑ ???= 0 ; ∑ ??y= 0; and ∑ ???= 0 where o is an arbitrary point. (you have three equations to solve three unknowns)
please mention every step thanks
A 100 KN force applied on a beam of 3m long, if the cross- sectional area is 500 mm2 and E= 200 GPa, the deflection ŏ of the beam is: O a. 1mm O b. 2 mm O c. 4 mm o d. 3 mm
At the instant shown, the slider D has a velocity of 3 ft/s up the channel and its speed is decreasing at a rate of 0.5 ft/s². Determine at this instant: a. The angular accelerations a and acp (include magnitude and direction) b. The acceleration of point C in Cartesian form. Solve the problem using any method. 3.a a AB acD 3.b ac = = 10 in. 8 in. A B 12 in. D 30°
Solve the problem by the moment-area method. The beam has constant flexural rigidity EI. A simple beam AB supports two concentrated loads P at the positions shown in the figure. B C 4. 4 A support C at the midpoint of the beam is positioned at distance d below the beam before the loads are applied. Assuming that d = 12 mm, L = 5.4 m, E = 200 GPa, and I = 193 x 10° mm, calculate the magnitude of the loads P (in kN) so that the beam just touches the support at C. 163.87 x kN
A beam supported by three identical springs at points A,B,C (see figure). Given that flexural of rigidity of the beam, EI= 2.029X1011 N.mm2 ; spring constant,k = 1471.5N/mm, w=116N/mm All dimensions are in mm. 1. What is the reaction for at point A,B and C? 2. What is the deflection at point B? 3. Please draw shear-force and bending moment diagram.
A simply supported beam is subject to a downwards uniform distributed load, w, as shown below. B A uniform distributed load, w L1 L2 The cross-section of the beam is constant with second moment of area I = 3750 mm², and Young's elastic modulus is E = 200 GPa. The distributed load has magnitude w = 220 N/m. If Point B is distance L₁ (Point C), calculate: the downwards vertical deflection at Point B: C C 435 mm from the left end (Point A) and distance L2 = 385 mm from the right end Round your answer to 3 significant figures. X [Units: mm]
Determine the internal moments at the supports of the beam shown using: 1.) ThreeMoment equation 2.) Moment Distribution Method 3.) Slope-Deflection Method Pick two method only Given: E=200GPa I=20x10^6 mm^4 w=8kN/m L1=10m L2=8m