Two hard rubber blocks are used in an anti-vibration mount to support a small machine as -140 lb causes a downward deflection of 0.23 in. Determine the shear modulus of the rubber blocks. Assume a-0.50 in.b-0.95 in, and c-2.70 in. Determine the shear strain from the angle formed by the downward deflection and the block thickness a. Do not use the small angle approximation tanyy. Enter a positive value for y Answer y rad

Two hard rubber blocks are used in an anti-vibration mount to support a small machine as -140 lb causes a downward deflection of 0.23 in. Determine the shear modulus of the rubber blocks. Assume a-0.50 in.b-0.95 in, and c-2.70 in. Determine the shear strain from the angle formed by the downward deflection and the block thickness a. Do not use the small angle approximation tanyy. Enter a positive value for y Answer y rad

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the equivalent stiffness constant of the ff.
3. If P= 100KN, Compute the total deformation. 112 in 201 60 CM 90 cm 9p 4P 7P $=2ch $=6m 644ch E= 120 GPa E = 200 GPa = 100 GPO
A solid circular rod 200 mm long and 20 mm in diameter has an axial force of P. are exposed. P force and elongation of the rod when this force is applied is below the elasticity of the material, taking as the values given opposite your names in the table presented Calculate the modulus E and the shear modulus G. Take the Poisson's ratio () 0.3. P (N) δ(mm) :500 1,6
a) Calculate the principal strains, given that the state of plane strain for an element is: E = 25microns E, = 100microns Yy =-45microns b) An axial load of 3 kN is applied to the solid tubular member as shown in Figure 1. The length of the tube is 2.5 metres, the radius is 15 mm. The modulus of elasticity is 200 GPa. Calculate the elongation due to the loading, giving the answer in microns. Length of tube: 2.5m 8 Load: 3 kN Radius of tube: 15mm Figure 1
The tube has a length of 2 m and is made of the material with the properties provided in the following figure. (a) Determine the torque needed to just cause the maximum strain to reach 0.015. (b) What is the permanent angle of twist of the tube when this torque is removed?
answer quickly
A helical spring used in an automobile suspension is having a wire diameter of 7mm and an outside diameter of 72mm. The spring has 16 active coils. If the permissible shear stress of the spring material is 345 N/mm2 and the Modulus of rigidity is 83 kN/mm2. a) Calculate the axial load in N and the deflection of the spring in mm, considering the effect of curvature. b) Calculate the value of axial load in N neglecting the effect of curvature.
please help answer and explain
solve first one only and use b h and x to find the strain
Solve following the problems below and show your complete, systematic and neat solution. Upload your solution with one PDF file. 1. For the beam shown, a. determine the maximum flexural stresses in compression ant tension. b. determine the flexural stress of the fiber located at 3m from the left support and 50 mm above the bottom 18 kN/m 300 mm 6 kN/m 20 mm 27 kNm 22 2m 2m 3 m +m 15 mm - - 50 mm 360 mm 20 mm
3. The elastic portion of the stress-strain diagram for a titanium alloy used for medical implants shown. The specimen from which it was obtained has an original diameter of 10 mm and a gage length of 45 mm. If a tensile load of P = 300 kN is applied to the specimen. Take Poisson ration 0.3. a) determine specimen's new length after deformation. b) determine specimen's new diameter after deformation. Make sure to include the calculation for all steps including E and longitudinal and lateral strains MPa 700 600 500 400 300 200 100 E 10-3 10 15 (Ans:lnew - 46.718mm, Dnew - 9.885mm, ) for tregting
250 mm Q1: The beam shown in Figure 1 is subjected to a vertical force Py and a horizontal force Pr The data for P Pr, a L,and e are shown in Table1. Determine the maximum compressive and tensile stresses under the vertical force (at a distance a from the left support.) Pv > 135 KN 55 omm a I=> 6omm Ph 2248KN 120 mm L =2 600mm Figure 1