Turnbuckle T₁ is tightened to a tension of 160 lb and turnbuckle T₂ is tightened to 98 lb. Determine the components of the corresponding force and moment reactions at the built-in support at O. Neglect the weight of the structure. Answers: Ox= Oy= Mx= My= 36" O₂ = 224 M₂ = 43.8 82 IM i 32" 24" 24" 36" lb lb lb 7₂ 18" lb-in. lb-in. lb-in.

Q: Determine Iy. 50 mm 50 mm 300 mm 50 mm y -200 mm an -X We Problem 4

A:

Q: For the problem shown below, you are given x1 = 0.28 m, x2 = 0.05 m, x3 = 0.18 m, and y1 = 0.07 and…

A:

Q: A conveyor 66 m long is inclined at an angle of 4 degrees to the horizontal and deposits material 8…

A:

Q: State the difference between the eutectic and eutectoid points.

A: Eutectic point: In the iron carbon phase diagram at 2 percentage of carbon is called eutectic point.…

Q: 80mm 60mm Vax's Gomm 40mm Find the location of the Controid. Show All work. 1

A:

Q: The solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T =…

A: Given data T = 320 N-m The allowable shear stress for the material is Tallow = 185 MPa.

Q: the hole of radius 16 mm and thickness 18 mm. Dimension A = 52 mm; B = 51 mm.  determine its volume…

A: Volume can not be negative.

Q: Express the quantity 556.2 x 10^-12s in fs.

A: Given Data: The time given is t = 556.2×10-12 s. The conversion of second to femtosecond can be…

Q: Assume F-9 kN. Using RECTANGULAR COMPONENTS, determine the direction of the resultant force,…

A: To find: The direction of the resultant measure counter clockwise from the positive x-axis. Given:…

Q: I want the methode of counting this two drawing L, and J1 and J2 veryy urgent

A: Full joints are the revolute joint and half joints are the sliding pair.

Q: Find the unit for H. Show all steps

A: Given, all the units of each parameter Substituting these values in the above equation,

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 2. Determine the reading on the vernier scale as indicated by the arrows. 25 30 35 40 10 20 30 40 50…

A: Least count of Vernier caliper = 0.02 mm

Q: - х a = 6 in b = 0.7 in C = 2 in

A:

Q: Question 24 In the same setup as in question 23, if the mass of the crane arm (including winch) is…

A: Solution for Question 24: Given, Mass of arm = m = 100 kgWeight of arm = W = mg = (100) (9.81) = 981…

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: gure 0.5 ft 1 ft G 2 ft 0.25 ft int < 1 of 1

A: Given,

Q: The volume of the syringe’s reading read as 4cc when the weight (pressure) was 600 g. Determine the…

A: Initial Volume, V1=4 ccWeight for 4 cc volume, M1= 600gFinal Volume, V2=2.5 cc

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.