Try the following Problems Problem I The equivalent circuit of a 50 kVA 2400/240 V transformer is shown below. The transformer is connected to 0.8 pf lagging load at rated voltage at secondary terminals at rated kVA. The transformer efficiency and voltage regulation are found to be 97% and 2% respectively. It was found that copper loss 600 W. The impedance seen at primary terminals is 110 40° 2. Take Rel = 1.21 2 and R2=90.41 2. Find Xm2 and Xel Re1 Xel E E Xm2 Rc2

Try the following Problems Problem I The equivalent circuit of a 50 kVA 2400/240 V transformer is shown below. The transformer is connected to 0.8 pf lagging load at rated voltage at secondary terminals at rated kVA. The transformer efficiency and voltage regulation are found to be 97% and 2% respectively. It was found that copper loss 600 W. The impedance seen at primary terminals is 110 40° 2. Take Rel = 1.21 2 and R2=90.41 2. Find Xm2 and Xel Re1 Xel E E Xm2 Rc2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q27. Point charge +Qb (not shown) is being taken from A to C, and then lastly from C to B. Which path requires more work? * C +Qa В A to C A to C = C to B C to B B to C C to A
When the transformer is loaded in a balanced fashion up to its nominal rating (10 MVA), calculate the high side line-to-line phasor voltages (ab, bc, ca). and low side phasor voltages both line-to-line and line-to-neutral (ab, bc, ca, a, b,c). as a reference for calculations the low side A line to neutral voltage is 7620V at an angle of 0 degrees when the transformer is at rated power. The transformer has the following characteristics: V: 138kV delta high side/ 13.2 kV wye low side 9% impedance X/R ratio of 20
The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined. The open-circuit test and the short- circuit test were performed on the primary side of the transformer, and the following data were taken: Open-circuit test (on primary) Short-circuit test (on primary) 8000 V V= 489 V I0.214 A 2.5 A P= 400 W P= 240 W Find the impedances of the approximate equivalent circuit referred to the primary side, and sketch the circuit.
Why we used isolation transformer
A single phase 220/6 Volt, 50 Hz transformer has a rated primary current = 0.5 A. its maximum efficiency is at load current = 15 A and equal to 94% at unity p.f. Its efficiency at rated load, 0.65 p.f. lagging is: 087.8%. 092.3%. 090.9%. ONone.
In no load Phasor diagram of practical transformer, the core loss current Ic is with primary voltage Vp. O Lagging O in phase O Leading O 90 degrees out of phase
In a practical transformer, Identify, which component of no load current supplies eddy current loss? a. I0 b. IC c. IM d. None of these
Please solve the problem i want urjent
A 20 kVA, 2000/200-V, 50-Hz transformer has a high voltage winding resistance of 0.2 and a leakage reactance of 0.240. The low voltage winding resistance is 0.052 and the leakage reactance is 0.02 2. Find the equivalent winding resistance, reactance and impedance referred to the (i) high voltage side and (ii) the low-voltage side. (Draw the related equivalent-circuits) @
A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 23 (line-to-line) kV. The step-down transformer has a turn ratio of 35:2 and it has a Y-connected, balanced load of 0.490 +j 0.0816 ohms connected to its secondary side. A capacitor bank of -j0.171 ohms is added parallel to the load. Assuming an ideal transmission line, the load voltage (line-to-neutral) would be: O A. 7360 V O B. 6.2 kV O C. 12750 V O D. 4806 V O E. None of the other choices are correct
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.