true false at read cycle high MEMR signal at T2 indicate that data is

Q: Flat top sampling is obtaining by multiplier analog signal by pulse signal True False

A: This statement is True as flat top sampling is obtaining by multiplier analog signal by pulse…

Q: In the Cyclic redundancy check (CRC) decoder, divide two occurrences.

A: Answer:-   Cyclic Redundancy Check (CRC):   A cyclic redundancy check (CRC) is an error-detection…

Q: What is meant by Hamming distance, and why is it important?What is meant by minimum Hamming…

A: Hamming distance is a method for comparing different streams of data in binary format. Hamming…

Q: Convert -21 as a nine bit sign magnitude number

A: Answer: As a general rule, we address the positive (unsigned) numbers with no sign and negative…

Q: Analog means continuous.

A: Given: Analog means continuous.

Q: Starting with the 16 bit unsigned world uint16_t word16, determine if bit 4 is set and bit 8 is…

A: Hi student, hope you are doing good. The C code is attached below along with proper explanation of…

Q: What is the operation of an adaptive mutex?

A: An adaptive mutex is used to protect any significant data item accessed by only a few lines of code.…

Q: MOV's second operand is the destination.

A: The MOV instruction moves data from the second operand, which may be a constant, a register, or a…

Q: What affects does delay skew have on the signal?

A: Intro What effects does delay skew have on the signal?

Q: 3-make deconvolution between two signals as shown deconv. x(t) h(t)

A: the solution is an given below ";

Q: Dividing two occurrences will activate the CRC decoder

A: Cyclic Redundancy Check (CRC):   We know A cyclic redundancy check (CRC) is an error-detection…

Q: 11. Unused states are treated as Don't care conditions during

A: Required:

Q: In what manner is the delay time quantified, and what units are used to describe it?

A: Latency: Latency is the number of seconds it takes a network to transport data from one device to…

Q: The purpose of a biased exponent, and what it is.

A: A computer is a digital electronic machine that can be programmed to automatically perform a series…

Q: Convert -47 to sign magnitude form using 8 bits. Show your steps.

A: To convert a decimal number to sign magnitude form two steps are there:- 1. Change the number to…

Q: Which operation is represented by this truth table? AB out 101 110 001 0 11 O XOR O NAND OR O NOT

A: NAND gate The logical NAND gate is opposite to AND gate. It performs on the complements of the…

Q: Write a program to monitor the RB5 bit. When it is HIGH, make a LOW-to-HIGH-to-LOW pulse on RB3.

A: Write a program to monitor the RB5 bit.When it is high,make a LOW-to-High-to-low pulse on RB3.

Q: Write a function to count the number of events (negative transitions) in pic18f45k50. The number of…

A: Solution:void event_counter(void){ TOCON=0x01; // Initialize TOCON TMRO = 0; // Clear TMRO while…

Q: use of a parity bit rests on tow basic assumpions  a-probaability of errors occurring is small…

A: Parity bit The parity bit is also called a check bit. This check bit is added for error detection…

Q: 00000110b in ASCII stands for End of Transmission Select one: True False

A: Solution:   Given,

Q: Write Excel Vba code using Simpson's 1/3 rule for this formula Asin2Bx

A: Simpson's 1/3 formula is used in the approximation of the integrals. Simpson's formula is just the…

Q: Quantization process is carried out during digital to analog conversion process. Select one: O True…

A: The given information regarding Quantization.

Q: Using a shift operation, write MIPS code that divides the number in $t2 by 8.

A: .data  before: .asciiz "Before : " endl: .asciiz "\n" after: .asciiz "After: ".text li $t2, 200 #…

Q: In Quantization step, if the minimum value is 1, the maximum value is 32, and the number of bits is…

A: Quantization step size = Size of Range / 2no. of bits - 1Size of the Range = Maximum Value - Minimum…

Q: 4. Using a combination of ASK, FSK and PSK: a) Sketch the unique signals, one each for 011, 100,…

A: ASK (Amplitude Shift Key) In ASK  amplitude of the carrier wave is changed (switch) according to…

Q: What is the IEEE single-precision hex representation for -27.6015625? (in hex)

A: Explanation and calculation:: We need to convert the number into (32 bit) single precision binary…

Q: Please enter the expected signal values in the highlighted boxes, based on the circuit's input.…

A:

Q: PCM is a technique used in CODECS to convert analog data to digital form Select one: O True O False

A: Pulse code modulation (PCM) is a digital scheme for transmitting analog data. It converts an analog…

Q: f) The period of a signal with frequency 0.5 MHz is seconds.

A: Given that, Frequency of signal= 0.5 MHz

Q: Signal to noise ratio is calculated as signal voltage divided by noise voltage Select one: O True O…

A:

Q: Dividing two occurrences will activate the CRC decoder.

A: CRC: Cyclic Redundancy Check: A standard error-detection method used in digital networks and…

Q: If the output signal shown in the figure below is active low, what is the duty cycle? Output Count…

A: The solution of the given question to find the duty cycle is given below.

Q: Synchronization bit at the beginning of character is called start bit explain?

A: Synchronisation is the process of collecting data in real time from source node. The whole process…

Q: Junto level 1 Check 0 0 Add 5 and 0 0 O Next 0 7 0 0 Carry bits 41 0 Result number

A: Binary addition can be defined in such a way that it is one of the binary operations.To take into…