True False 1 Continuous discharge is the discharge which is supplied continuously with the time. 2. Intermittent discharge is the discharge which is supplied through part of the time and discontinued through another part. 3 Intermittent discharge of 0.49 m^3/s is applied for 2 days once every 2 weeks, the required continuous discharge would be 70 Ips.

True False 1 Continuous discharge is the discharge which is supplied continuously with the time. 2. Intermittent discharge is the discharge which is supplied through part of the time and discontinued through another part. 3 Intermittent discharge of 0.49 m^3/s is applied for 2 days once every 2 weeks, the required continuous discharge would be 70 Ips.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The discharge through a concrete pipe of 1 ft diameter and 3000 ft length is 1.0 cfs. What is the head loss (hf) if the water temperature is 60°F? Apply the Darcy- Weisbach equation
How can I calculate the specific discharge for the z-axis( qz)? specific discharge formula: qz = -Kz*(dh/dz) Terms: K = Hydraulic Conductivity dh/dz = Hydraulic Gradient h = Hydraulic Head z = length Hydraulic heads aren't given for the z-axis so I'm struggling on how to calculate for those values and I need them to solve for specific discharge.
Question 2 For the water distribution system shown below, find: (a) The discharges in the loops (b) Pressure heads at point B, C, and D if the pressure head at point A is 80 m and A, B, C and E have the same elevations All pipes are 1 km long and 300 mm in diameter with roughness f-0.03, 90 L/s A E 1 km 300 mm B D C 60 L/s D
Three pipes of different lengths and diameters connected in series as shown discharges 169 lit/sec. If f=0.012 and disregarding minor losses, determine a. the head loss in each pipe. b. the diameter of an equivalent single pipe that could replace all the 3 pipes. ASAP
Water Gs=1 1. In a test to determine the discharge coefficient of a 70 by 35 mm Venturi meter, the total weight of water passing through the meter in 5 minutes was 3.5 kN. A mercury differential gage connected to the inlet and throat of the meter showed an average mercury difference during that time of 300 mm.. Determine the actual discharge if the same meter is used later on and a 250 mm difference is then observed. Mercury, Hg Gs = assume, 4 significant figures 2. The diameter of a 3 meter pipe decreases from 450 mm to 150 mm. If the velocity is to decrease uniformly in a linear manner, draw the diameter profile at each 500 mm length interval along the pipe. Discharge is 150 liters per second. Reservoir B 3. A pump draws water at 300 liters per second from reservoir A and lifts it to reservoir B as shown. The head loss from A to 1 is 20 times the velocity head in the 200 mm diameter and the head loss from 2 to B is 20 times the velocity head in the 150-mm diameter pipe. Assume your…
The discharge through a concrete pipe of 1 ft diameter and 3000 ft length is 1.0 cfs. What is the head loss (hr) if the water temperature is 60°F? Apply the Darcy- Weisbach equation
Three pipes 1, 2, 3 are connected in parallel. The properties of each pipe are given in the table. The combined discharge of the three pipes is 0.61 m3/s. Use Hazen-Williams coefficient of 100 for all pipes. Use table below for the properties of the pipes. a.) calculate the total head loss (A. 181 m B. 461 m. C . 411 m. D. 731 m) b) Solve for the rate of flow in pipe 1 ( A. 0.1249 m3/s. B. 0.1645 m3/s. C. 0.1145 m3/s. D. 0.1225 m3/s). C.) c) Calculate the rate of flow in pipe 2. ( A. 0.1032 m3 /s. ,B. 0.1255 m3 /s. C. 0.7865 m3/s. D. 0.3955 m3/s)
A sprinkler head has a discharge rate of 22.5 gal./min and a coefficient K = 5.65. What pressure is required at the sprinkler head?
Dechlorination contact tank (Wastewater Treatment) An activated sludge plant has a design flow (average daily flow) of 11 MGD. Determine dimensions of dechlorination tank. The design parameters: use 1 tank. detention time = 30 sec, depth = 10 ft, rectangular tank: L = 4 W. use maximum hourly flow (3 * Average design flow)
1. A pipe network consists of the following pipes: pipe AB is 20 cm in diameter and 700 meters long; pipe AC is 25 cm in diameter and 800 meters long; pipe BC is 15 cm in diameter and 900 meters long; pipe BD is 15 cm in diameter and 100 m long; and pipe CE is 30 cm in diameter and 50 m long. An inflow of 0.20 cubic meters per second enters the system at junction A and 40% of this discharge flow on pipe AB. If Cw for Hazen-William's Equation is 122 for all pipes, determine the discharges in pipes BD and CE.
The elevations of water surfaces in reservoirs A and B are 300 ft and 250 ft, respectively, and discharge Q1 = 50 ft2/s. Determine the following: (a) head loss (ft) in pipe 1, h1, (b) the elevation (el D') of the imaginary water surface at the junction, (c) the head loss (ft) in pipe 2, hL2, (d) the flow rate (ft³/s) in pipe 2, Q2. (e) the flow rate (ft/s) in pipe 3, Q3. (f) the head loss (ft) in pipe 3, hL3, (g) the elevation of the surface of reservoir C, El C. pipe L (ft) d (in) 1 5000 36 0.0157 2 1500 24 0.0162 3 4000 18 0.0177 A B D