Transistor parameters in the given amplifier circuit are Kn=1mA/V?, VTN=1V, A=0 Cas=0,1pF Cgo=1pF a) Determine the Dc operating point of the transistor. In which region does the transistor work? b) Draw the small signal equivalent of the circuit. c) Determine the low frequency transfer function and cutoff frequencies for C1 = 1mF C = 10mF. d) Draw the high frequency equivalent of the circuit. Determine the high cutoff frequencies he=2,5K

Transistor parameters in the given amplifier circuit are Kn=1mA/V?, VTN=1V, A=0 Cas=0,1pF Cgo=1pF a) Determine the Dc operating point of the transistor. In which region does the transistor work? b) Draw the small signal equivalent of the circuit. c) Determine the low frequency transfer function and cutoff frequencies for C1 = 1mF C = 10mF. d) Draw the high frequency equivalent of the circuit. Determine the high cutoff frequencies he=2,5K

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

answer part b,c, and d
solve it in less than 30 min pls.
1. To use the Bipolar Junction Transistor (BJT) as a small signal amplifier it must be biased in this region: A. South Park region B. Spatial interface region C. Inverse Thevenin region D. Linear or active region
2. The parameters of the transistor as shown in the figure below are ß = 100 and VA = 100V. a. Find the dc voltages at the base and emitter terminals. b. Find Rc such that VCEQ = 3.5V. c. Assuming Cc and CE act as short circuits, determine the small-signal voltage gain Av = Vo/Vs. d. Repeat part (c) if a 5000 source resistor is in series with the vs signal source. V+ = +5 V Rs = 100 £2 www Us Cc RB = 10 ΚΩ I= Iausmi 0.35 mA www RC -000 V=-5 V CE
Subject : Electronics Engineering Draw and explain a small signal high frequency CE model of a transistor.
Please answer question a and b
(b) The multistage amplifier circuit of Figure Q.2(b) have the following parameters: Qı and Q2: B= 200, VBE = 0.7 V, VT = 26 mV , VA=∞ Given that Icọ1 = 2 mA and VCEQ1 = 2 V. (i) Determine the value for R84. List the assumption/approximation made in the analysis. (ii) Sketch and label the small-signal hybrid-t equivalent circuit at midband frequency range. (iii) Calculate the small signal hybrid-n model parameters: gm and ra for Qı and Then, determine Zi2 and Zo. VSI (iv) Find +15 V TU MA RBI 100 k2 UNIVERSITI { Rc 3.3 k2 RB3 10 kN IcQI Q2 C4 Qi VCEQI Ro TEO ► 50 k2 Rs 100 2 RL V. 10k2 RE 2 kN RB4 C3 Zi2 Z, Figure Q.2(b) AYSIA
When an AC signal is supplied to a CE amplifier, the input signal moves the operating point O a. Along the AC load line Ob. Between the AC and DC load lines OC. Nowhere O d. Along the DC load line
For the circuit given below, transistor parameters are given as -= 0.1mA/V², Vth,p=-1V, A=0. Using these information, a) Design the circuit (find the values of R1and R2) such that Ip=100HA. b) Find the small signal voltage gain Vo/Vi of the circuit. R1 10 V - R2 ww0-2.5 V
For the p-channel JFET circuit in the Figure, the transistor parameters are: /oss = 2 mA, Vp = |1.75| V. (a) Determine Ipo and Vspo- (b) Give the small signal model (c) Determine the small-signal voltage gains Av = vo/vi QUESTION I: For the p-channel JFET circuit in the Figure, the transistor parameters are: Ioss = 2 mA, Vp = |1.75| V. (a) Determine Ipo and Vspo- (b) Give the small signal model (c) Determine the small-signal voltage gains Av = vo/vi VDD = 10 V Rg = 5 k£2 R1 = 90 kQ %3D Cc2 RL = 10 k2 R2 = 110 k2 ww
Which of the following models can be used for BJT AC SImall signal amplifier circuit analysis? i. hybrid model ii. re model iii. transconductance model iv. Eber's Moll model II, ili and iv i,i and iv O ii and iv O i and ii
Q6. Determine small signal voltage gain if VCEO =4.5 V. Transistor parameters (NMOS): k, = 100 pA/V, VIN-1 v, and A= 0.01 V. Transistor parameters (BJT): B = 100, VaE(on)= 0.7 V, and VA=00. 10V 8V Yo -38.08 b. -47.48 Oc -56.84 d-77.54 -66.15 -30.57