Total suspended particulate matter concentration in ambient air is to be measured using a high- volume sampler. The filter used for this purpose had an initial dry weight of 9.787 g. The filter was mounted in the sampler and the initial air flow rate through the filter was set at 1.5 m³/min. Sampling continued for 24 hours. The airflow after 24 hours was measured to be 1.4 m³/min. The dry weight of the filter paper after 24 hours sampling was 10.283 g. Assuming a linear decline in the air flow rate during sampling, what is the 24 hour average TSP concentration in the ambient air(in 10-6 g/m³?

Total suspended particulate matter concentration in ambient air is to be measured using a high- volume sampler. The filter used for this purpose had an initial dry weight of 9.787 g. The filter was mounted in the sampler and the initial air flow rate through the filter was set at 1.5 m³/min. Sampling continued for 24 hours. The airflow after 24 hours was measured to be 1.4 m³/min. The dry weight of the filter paper after 24 hours sampling was 10.283 g. Assuming a linear decline in the air flow rate during sampling, what is the 24 hour average TSP concentration in the ambient air(in 10-6 g/m³?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the total area required for placing the quarry tiles on the internal walls in this bathroom, given that the wall height is 2300, bathtub size is 1650x800x50, bathroom door size is 770x2500. BATHI 1650 (A) (B) 17165000 mm². 19090000 mm². 19879500 mm². (C) (D) None of the above. 0 200 ¹125
3) en= 24!-0" SIMPLY 8'-0" TYP %3D SUPPORTED ら000 psi fィ= 6o Ksi WoL= 29,5" 1.25 kLF 3-#9 :CHECK Er >0.005 FIND AレLOWABし Wn USE 1.2ウ+ioL
i need the answer quickly
Course No. Problem No. 291.1 mmm. Find the internal force A 10₁-41² 220 mm TAY=SON =50N 270mm B www.lb Assignment No. ६ By ↓ 100N 02-6230 ·100mm- X 540 mm in each member C Date F 01 - 41⁰ 02= 62.30 0₁=4100 220mm Page of D 1DY = Son
Please complete table and show solution
Compute the moment of inertia for the built up section shown below about the strong axis only.
What is the amount of loadthat applied to the center ofthe rectangular concrete beamsample if the Modulus ofRupture is 3.50MPa?Length of the sample = 550mmDimension: 150mm x150mm
Draw sfd and bmd
4.29 (Ans. VA = 68.96 k 1, VB = 157.79 k ↑) A 80 k 100 k 30 ft 4.30 50 40 ft ft -120 ft- B 40 ft 60 ft 60k 30 k ↓↓ Hinges 30 20 30 ft ft ft -80 ft- 200 ft- Hinges 60 ft C 50 k 40 ft 4 klf D -80 ft- -120 ft- 4.34 2 40 ft
人工知能を使用せず、すべてを段階的にデジタル形式で解決してください。ありがとう SOLVE STEP BY STEP IN DIGITAL FORMAT DON'T USE CHATGPT Design the longitudinal steel and the cross section of the beam shown, consider concrete that indicates fy = 4200 kg/(cm²), 1/2 stirrups and 2.5 cm coatings. 1m 0.5T 2m 0.2T 6.5m Calculate top rods per steel (min) asmin If f'c = 200kg/cm² 1.5T/m
1. Determine the degree of indeterminacy. A. 0 B. 1 2. Determine the degree of indeterminacy. A A. 0 B. 1 3. Determine the degree of indeterminacy. A. 0 B. 1 B C. 2 D. 3 W C. 2 D. 3 C. 2 D. 3 C +² in D
Geotechnical