To synthesize titanium (IV) chloride, the reaction below is used. 3TIO2(s) + 4C(s) + 6CI2(g) → 3T¡CI4(g) + 2CO2(g) + 2CO(g) If 35.0 g of TiO2, 45.0 g of Cl2, and 11.0 g of C were used in the preparation, how much of the excess reactant with lesser initial moles remained after reaction has stopped? Use the following values for the molar masses: C = 12.01, CI = 35.45, O = 16.00, Ti = 47.87, and express the answer in grams with three significant figures.

To synthesize titanium (IV) chloride, the reaction below is used. 3TIO2(s) + 4C(s) + 6CI2(g) → 3T¡CI4(g) + 2CO2(g) + 2CO(g) If 35.0 g of TiO2, 45.0 g of Cl2, and 11.0 g of C were used in the preparation, how much of the excess reactant with lesser initial moles remained after reaction has stopped? Use the following values for the molar masses: C = 12.01, CI = 35.45, O = 16.00, Ti = 47.87, and express the answer in grams with three significant figures.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

35 - How many mL solution should be taken from 0.900 M K2SO4 solution to prepare 250 mL of 0.450 M K2SO4 solution? A) 45 B) 95 C) 125 D) 15 E) 25
Sodium hydroxide (NaOH) is a reagent in the form of crystals and is highly hygroscopic. It is advisable to standardize it when it is desired to use it in acid standardization solutions. Knowing that 12g of the base (NaOH) were used to prepare 1L of solution, determine the actual concentration of the solution (NaOH) for a 50mL sample where 55 mL of 0.3N hydrochloric acid were used, and the volume of the said base to prepare 1L of 0.01N solution. (Data: Molar Mass of NaOH = 40.0g/mol).
Unstable and perishable medicines include: A) 1, 2, 3 1) Diluted hydrochloric acid B) 1, 3 2) Alcohol solution of iodine B) 2 and 4 3) Formaldehyde solution D) 1, 2, 3, 4 4) Hydrogen peroxide solution E) 1, 2, 3, 4, 5 5) Isotonic sodiumchloride solution (Give the answer in the form: A3, B1, etc.)
Graph: a) InC versus 1/T graph to determine the entalphy of solution. Show your calculations on the graph. - 10-77 - 10.08 -9.79 3.35x 10-3 3.25x103 3.14 c103 3.05x 10 2.96* 10-5 InC - 10.41 -9.50 1/T (K-')
physical chemistry, please solve question 2
Draw a schematic diagram using this information. Preparation of the solution Take about 25-30 ml of distilled water in a beaker and add powdered crude copper sulphate while stirring the solution so that the powder dissolves. Keep adding the powdered sample till a little of it remains undissolved, even if it is stirred thoroughly. Now add 2-3 ml of dil. H2SO4 to make the solution clear. This prevents the hydrolysis of copper sulphate. Filtration of the solution Take a funnel and fix a filter paper in it and clamp it to a stand. Place a china dish under the funnel. The stem of the funnel should touch the wall of the china dish to avoid the solution splashing out. Pour the solution into the funnel over a glass rod and collect the filtrate in a china dish. The insoluble impurities are left in the filter paper as residue. Concentration of the filtrate to crystallisation point Heat the china dish on a sand bath till the solution is reduced to about one-third of its original volume. To…
Molar concentration of the bleach stock solution: .134 mol/L Solutions(Dilutions) Concentration% Experiment 1 0.25 Experiment 2 0.50 Experiment 3 1.0 Fill in the OCl- molar concentrations for each experiment. Solutions(Dilutions) OCl- Concentrationmol/L Experiment 1 Experiment 2 Experiment 3
o NB3: What is the dilution factor of the 50 mM stock solution relative to the 1 mM solution? Relative to another 100 mM stock solution?
Create a flowchart for the procedures in the determination of water hardness.
Rewrite as a logarithmic equation. 10 = 2 Dlog O Olog0 No D=0 solution
Considering the procedure below: “Determination of the concentration of HCl: Pipette 10 mL of hydrochloric acid and transfer to a 100 mL volumetric flask, complete the volume with water and homogenize. Remove a 10 mL aliquot of this solution and transfer it to a second dilution in a 100 mL volumetric flask, complete the volume with water and homogenize. Take a 20 mL aliquot of this last solution and transfer to a 250 mL erlenmeyr and add 20 mL of distilled water and 4 drops of the acid-base indicator. Titrate with a previously standardized 0.100 mol/L sodium hydroxide solution until the indicator turns.” Answer: a) In this titration, the indicator used is phenolphthalein. Discuss the use of this indicator considering its turning range and pH at the stoichiometric point of the titration. Justify. b) Considering that the volume of titrant used was equal to 24.5 mL, calculate the concentration of HCl in the sample in mol/L.
Part A To what volume should you dilute 25 mL of a 11.0 MH₂SO4 solution to obtain a 0.160 M H₂SO4 solution? Express your answer using two significant figures. 195| ΑΣΦ V Submit Request Answer PMC ? L