To solve the Commutation Problem in large machines, this can be achieved by increasing the brush width The effect of armature current on main field flux is armature reaction

Q: If the four input lines of a multiplexer are DO, D1, D2 and D3, and the two select lines are given…

A: Four input lines of a multiplexer, and input for the select lines are 11 then find the output of…

Q: QUESTION 10 The data compare instruction is used to compare data stored in one or mo True False…

A: PLC based choose the correct answers:

Q: Based on the given signals of f[n] and g[n] in Figure 1, sketch the operation of the signals s…

A: Given: spectrum of F(n) and g(n) Find the above questions

Q: Identify the type of signal as shown on the following figures. Also, indicate the equation defining…

A:

Q: According to the code below, all jumps are short jumps, meaning that the abels are in the range -128…

A: according to the code below, all jumps are short jumps meaning that the labels are in range: -128 to…

Q: 9. For the SR Latch discussed in the lecture slides, output Q is only observed at select times…

A: Given that for SR latch is,                                            the sequence of Q for SR flip…

Q: What is FSM?

A: FSM stands for finite state machine which is used for the simulation of the sequential logic or it…

Q: Sheugg aud Parwe finibe Sigeel Exampue Gheugy No neel

A: Yes, we have to find power and energy of given signal. The power calculations of your answer is…

Q: In your own words, explain why a good linearity is desired in most of the sensors and. Please be…

A: The following question is based on sensors. A sensor is a device that converts a signal from one…

Q: 11. What is the count range of the Asynchronous counter shown below? T 12. CLK 30 30 SCLE 74LS76N…

A: Given counter is Asynchronous Counter because clk is given first flipflop and then output of first…

Q: A. Which of the following statements about equalization is false? Select one: a. It can help reduce…

A: Solution a) option d, If the channel is fast, it gives more weight to the current received signal b)…

Q: How many select lines are required for a 1-to-8 demultiplexer? Select one: a. 4 b. 3 Cc. 2 d. 5

A: Given data, Select lines requires in 1-to-8 demultiplexer.

Q: given that SSR = 50 and SSE = 100 calculate R2 ?

A:

Q: Q.26 Why is shielded wire used for signal runs? Select one: A. TO PREVENT VOLTAGE SPIKES B. TO…

A: From this question we need to know why we use shielded wire for signal runs :

Q: Assume that carry flag is 1 at the beginning, and execute the following code: mov al, OE8H rcl al, 1…

A:

Q: represents a circuit breaker with thermal overload protection? A. C B. D C. A D. B

A:

Q: A type of noise that is directly proportional to the frequency of the operation. a. shot noise b.…

A: Another quite noise that happens in transistors is referred to as transit time noise. Transit time…

Q: CLK T Positive Edge Triggered T Flip Flop LAH CLK T Negative Edge Triggered T Flip Flop I I

A:

Q: What is the Necessary condition to be applied in Laerangian functiong(L) to derive Power Balance E…

A: Pi =power output Necessary condition to be applied in Lagrangian function.

Q: QUESTION 10 With reference to the instruction below, what will be the value of each of the bits in…

A: We need to select correct option for given instructions .

Q: Where does 23/332 for N1/N2 come

A:

Q: w= 2nf b. 4xederf C. d. None of these

A: g(t)=2at2+a2in question ask ESD of g(t)Hint:Fe-at=aw2+a2Duality…

Q: Q1. For the circuit given below, find the inputs and outputs Q and Q' after four clock pulses. Write…

A:

Q: For specific system the root locus is plotted as shown in Figure (1). Are first method (or/and)…

A: The Ziegler-Nichols Act is a PID tuning law that seeks to generate positive values ​​in three PID…

Q: QUESTION 10 With reference to the instruction below, what will be the value of each of the bits in…

A: The destination of the CLR (clear) instruction has a value of bits. All of the bits in the…

Q: Hoow did the r13 equate to sq root of 0.5? when it shouldve been 0.2?

A: It is given that:

Q: Q1\ Find the counting state for the counter

A:

Q: Horizontal Controls Autoset tical Controls Trigger Controls

A:

Q: Please answer in typing format

A: 1) Signal Flow graph from block diagram: 2) No of Forwards paths = 1. Forward path…

Q: 2 If intrinsic impedance n1 = 355,91 and ɛ1=6,81, then ur1=? %3D (TT=3.14154 and take the decimal…

A:

Q: Q18/ Consider the CT signals shown in figure below. Calculate the power and then classify this…

A: Given: x(t)=2     -4<t<+40        otherwise

Q: not less than 5 sentences, how does a voltage regulator

A: In this question we will write about how voltage regulator work...

Q: 4- Can you trigger the TRAIC in (Q1 or Qıv), explain briefly?

A: Semiconductor are the material made of pure Si or Ge or compound . They have conductivity in between…

Q: What's the maximum percent overshoot for this system with its closed-loop poles as shown? Jo Select…

A: We need to find out overshoot for given system.

Q: MLT-3:- this encoding , imtally deca bts it will be represented occure d it will be vepresen ted Ir…

A: Given, Data =(A9)16  MLT-3 encoding:

Timers, Counter and Totalizers

In electronics, timers are solid-state specialized clocks that are used to measure specific time intervals. Time clocks are generally classified into two types. They are stopwatches that are meant for counting time in the increasing order starting from zero. The other type that is extensively termed in electronics is the timers. These are the devices that count in the decreasing order from a specified setpoint or time margin.