To provide some perspective on the dimensions of atomic defects, consider a metal specimen that has a dislocation density of 104 mm-2. Suppose that all the dislocations in 1000 mm3 (1 cm3) were somehow removed and linked end to end. How far (in miles) would this chain extend? Now suppose that the density is increased to 1010 mm-2 by cold working. What would be the chain length of dislocations in 1000 mm3 of material?

To provide some perspective on the dimensions of atomic defects, consider a metal specimen that has a dislocation density of 104 mm-2. Suppose that all the dislocations in 1000 mm3 (1 cm3) were somehow removed and linked end to end. How far (in miles) would this chain extend? Now suppose that the density is increased to 1010 mm-2 by cold working. What would be the chain length of dislocations in 1000 mm3 of material?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

...to the dislocation In mixed dislocation, the slip vector is O A. Nether parallel nor normal O B. Parallel O C. Both parallel and Normal O D. Normal
In the cubic structure, there are mainly 3 elastic constants including C11, C11, and C44. Now, in my simulation, the value of C11 is becoming very high due to applying pressure. So far, in the simulations I've done, it's reached around 570 GPa. If more pressure is induced, it could increase further. My question is, is this increase normal?
Explain why BCC (body-centered cubic) materials generally have higher mechanical strength values than FCC (face-centered cubic) materials in terms of (a) slip systems and (b) extended dislocations.
A metal has a certain fraction f = 105 of vacancies at the atomic level at finite temperatures. If the activation energy for vacancy formation was increased by 50%, what would be the new vacancy concentration? Select one: a. 7.43E-10 b. 6.22 E-5 C. 1.24E-6 O d. 3.16E-8 e. 5.48E-4
If ß-Sn, a tetragonal crystal (point group 4/mmm, a = 0.583 nm, and c = 0.318 nm) is subject to a tensile stress of 63 MPa along [100] and to a shear stress of 18 MPa on the (100) plane in the [010] direction. Determine: a) the tensile stress normal to (110), and b) the shear stress on the (110) plane in the [1-10] direction.
Your supervisor gives you four specimens all of them produced by Lead (Pb), that has atomic mass = 207.2u, atomic number = 82, melting temperature = 327.5 C, and then ask you to make a creep test for all ofthem to know the creep rate and at what temperature will it occur?
The following figure displays both an Edge Dislocation and a Screw Dislocation. Answer the following questions regarding the characteristics of each Dislocation Edge dislocation Screw dislocation
1
Your supervisor gives you four specimens all of them produced by Lead (Pb), that has atomic mass = 207.2u, atomic number = 82, melting temperature = 327.5 C, and then ask you to make a creep test for all ofthem to know the creep rate and at what temperature will it occur?
Calculate the dislocation spacing in a symmetrical tilt boundary (θ = 0.5◦) in a copper crystal.
Your supervisor gives you four specimens all of them produced by Lead (Pb), that has atomic mass = 207.2u, atomic number = 82, melting temperature = 327.5 C, and then ask you to make a creep test for all ofthem to know the creep rate and at what temperature will it occur?
Potassium (K) has the Body-Centered Cubic (BCC) crystal structure. The edge length is a = 0.533 nm. What is the linear density in atoms/nm along direction [011P Select one: a. 4.50 b. 6.37 O C. 3.18 d. 7.48 O e. 1.33 Europium has the Body-Centered Cubic (BCC) crystal structure shown in the figure below. The radius of the Europium atom is r= 0.204 nm. What is the planar density in atoms/nm in plane (20)? Plane (200)