To make peg adjustment, the following notes were taken, WYE LEVEL AT 1 0.632 2.543 Rod reading at P Rod reading at Q Point 1 is on the line PQ and midway between P and Q Point 2 is on the same line as P and Q but not between them. Point 2 is 30 m from P and 230 m from Q. With the wye level at point 1, what is the rod reading at Q for a level sight? a. 2.671 m C. b. 2.716 m d. 2.167 m 2.761 m WYE LEVEL AT 2 1.867 3.432 This includes primary, secondary, and working control on the objects on the jobsite. a. Referencing control b. Horizontal Control The angle of intersection of a circular curve is 45° 30' and its radius is 198 17 m If the PC is at STA 0+700 compute C. Monumenting Control d. Vertical control

To make peg adjustment, the following notes were taken, WYE LEVEL AT 1 0.632 2.543 Rod reading at P Rod reading at Q Point 1 is on the line PQ and midway between P and Q Point 2 is on the same line as P and Q but not between them. Point 2 is 30 m from P and 230 m from Q. With the wye level at point 1, what is the rod reading at Q for a level sight? a. 2.671 m C. b. 2.716 m d. 2.167 m 2.761 m WYE LEVEL AT 2 1.867 3.432 This includes primary, secondary, and working control on the objects on the jobsite. a. Referencing control b. Horizontal Control The angle of intersection of a circular curve is 45° 30' and its radius is 198 17 m If the PC is at STA 0+700 compute C. Monumenting Control d. Vertical control

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A level was set up in the middle of two pegs A and B and the staff readings were 2.015 and 1.895 respectively. The instrument was then set up at B and the readings on A and B were 2.195 and 2.005 respectively. What is the error in the line of collimation and reading on peg A which makes the line of collimation horizontal?
2. Complete the mising dota. UNE DISTANCE (meter) BEARING 1-2 123.4450 140.2336 146.3536 164.86 $73.45E N 18.19E $7421E S 19.71 W S81.90 W N 52.88 W 2-3 3-4 4-5 5-6 6-7 194.7219 7-1 96.3024
Prblm.
11. When an alidade and a plane table were set up over a point the elevation of the line of sight of the alidade was 406.29m. In order to determine the elevation of point M, the stepping method was used. The interval intercepted between the stadia hairs on a rod held on M was 1.95m. After the line of sight was depressed for five steps from the horizontal line of sight, the rod reading at the horizontal cross hair was 2.62m. Determine the elevation of point M.
Draw the cross sections and compute V. Two level sections of 40-m stations with center heights of 2.04 and 2.53 m. in cut, base width 15 m, side slopes 3:1. V₁ = A₁ + A₂ XL(m³) Vp L(A₁ + 4Am + A₂) 6 x 27 (yd³) Cp L 12 x 27 7(C₂₁ - 0₂) (W₁ w₂) (yd³)
4. An instrument is set over point "A" with a 5.45 ft. H.I. A vertical angle of -9°35'17" and a slope distance of 253.86 ft. were taken to a rod 5.17 ft. above point "B". The elevation of point “B" is 272.10 ft. What is the elevation of point “A"? (Draw a sketch to support your answer).
are taken (0 setting out @ HW: From the base line AB, the linear measurements (offsets) are ; EF. find CD . DE knowing that AB = 170°5- rectangular fence CD)
Determine ABL AB and ABL BC.
What is the bearing from Instrument A (Instru. A) to the Light post (Point D)? 110°20'35" 1000 E 5000 N Instru. A 335° 30' 45" 145° 30' 45" 65° 30' 45" O225°30' 45" 65°20'25" 1247.114 E 4751.420 N Light post Instru. B N
Please answer it. Thankyou
Draw the IL Lor By u and M. 5m
07: Water is flowing through apipe shown in Fig. what is the Difference in datum head (2₂-2₁), if the rate of flow through the pipe is (60 lit/sec). Jp Flookpo Ans: 2₂-2, -25.47m mm Datum line P₁ = 350kpa N 2