To develop a shear strength of 375 kN, find the spacing of 10 mm diameter stirrups consisting of 3 legs Given:Beam dimensions, b = 350 mm, h = 450 mmEffective cover to centroid of steel reinforcement = 75 mmConcrete f'c = 27.5 MPaMain reinforcement steel, fy = 415 MPaStirrups, fyv = 275 MPaShear strength reduction factor =0.75Beam is subjected to shear and flexure only

Answered: Image /qna-images/answer/80dc768c-56f3-4dba-9032-dd046ca15cb3.jpg

Answered: To develop a shear strength of 375 kN,…

Engineering

Civil Engineering

To develop a shear strength of 375 kN, find the spacing of 10 mm diameter stirrups consisting of 3 legs

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Using Method of Least Work find the Reactions at the supports. The Segment AB has a twice the moment…

Q: A simply supported beam of length 30-in has a circular cross section with a shoulder fillet at where…

A: Consider the free body diagram of the beam shown below. Consider the equilibrium moment about point…

Q: A rectangular section of size 100mm x 200 mm is used as a simply supported beam of 5m length. It is…

A: Given data : Width (B)=100 mmDepth (D)=200 mmLength of beam (L)=5 mCentral point load (W)=250 KNTo…

Q: Reinforce concrete beams DF, BE, and EH are 312 mm wide and 561 mm deep. The beams support a…

A: Slab dimension = 2.91m x 9.21 m Column width = 312 mmColumn depth = 561 mmDead Load, DL = 5.13…

Q: A 12m, I !!!2 Ar 10 kN/m 2m 2I I''² "I E = constt

A: Given data : Loading and dimensions are given Reactions at pin support are taken as Redundants. The…

Q: A solid steel circular shaft is required to transmit a torque of 1600 N - m without exceeding an…

A: Given that :- Torque = T = 1600 N-m Allowable shear stress = τmaxallowable = 55 N/mm2…

Q: Q1 The cantilever beam shown below, supports a concentrated load of 4 kN, a concentrated moment of 2…

Q: P 2 m 2 m そ L= 6 m Please find Maximum shear and bending moment with factored loads LiveLoad= 60kn…

Q: A reinforced concrete rectangular beam has a width of 315mm and an effective depth of 525mm. The…

Q: nt of forklift: 2,000 lb nt of load: 900 lb is at B are free to roll. mine the reactions a

Q: Determine the maximum shear stress in the beam with the cross section shown beside it. Be able to…

Q: a). What is the minimum diamétér of a solid 6m stéél shaft that will carry a shearing stress of not…

Q: A cantilever beam 6−ft6−ft long is made of steel, with a T-shaped cross section as shown below. If…

Q: Determine the bearing reaction and also the rod force from the truss structure above using the…

A: GIven, To determine,1. Support reactions.2. Member forces by Ritters method of sections.

Q: The beam carries varrying load as shown. Determine the following. Use Double Integration Method in…

Q: 2. A load P is supported by two steel springs arranged in series as shown. The upper spring has 20…

Q: The maximum bending stress (in MPa)

A: Given data, Simply supported beam having,width,b= 100 mm=0.1 mheight,h= 200 mm=0.2 mlength,l= 4…

Q: What is the spacing of stirrups at critical point?

Q: Q1) A uniform T-section beam is 50 mm wide and 100 mm deep with a flange thickness of 25mm and a web…

A: Question is based on the T beam subjected to uniformly varying load . Magnitude of load , dimension…

Q: A rectangular beam has a dimension of 210 mm x 260 mm. The simply supported beam is 5-m long and…

A: The values given in the question are as follows: Width of beam(b)=210 mm Depth of beam(d)=260 mm…

Q: If the 15-m-long cord AB can withstand a maximum force of 3500 N. determine the force in cord BC and…

A: Free body diagram :

Q: The distributed load shown in Fig is supported by a wide-flange section of the given dimensions.…

A: A) Given Data : Allowable flexural stress = 10 MPa Allowable shearing stress = 1.0 MPa To find ;…

Q: Design the width of a wooden beam if the depth is 380 mm, consider a simple span beam of 5 m in…

Q: Q2: A simply supported beam AB has a length of 3 m and carries distributed load which varies in…

A: Draw the free body diagram. Equilibrium of horizontal forces, ∑Fx=0Ax=0

Q: 2. The 5 m long beam AB has two types of distributed loads, and one concentrated load as shown. Find…

A: Given data Find support reaction.

Q: Problem 1: A W 410 x 100 is used as a girder to span 9 m on fixed supports at both ends. It carries…

A: Given: V = 82 kN Span, L = 9 m Beam section: W 410*100 Section details: d = 414 mm bf = 259.1 mm tf…

Q: Draw the free-body diagram for the following problem. The hand truck and load when it is lifted…

A: Draw FBD:

Q: depin a simple span beam of 8 m in length with overhang. a uniform load of 12.0 KN/m and its own…

Q: A concrete beam prestressed with a parabolic tendon is shown in the sketch. The eccentricity of the…

Q: Distributed load(s) of 50 kN/m may occupy any position(s) (either continuously or in patches) on the…

Q: The maximum shear force at a section is 78 kN. An ISWB of height 380 mm, breadth 200 mm, thickness…

Q: For the cantilevered strut shown below, determine the following: a) Maximum shear stress acting at…

A: Determine a. Maximum shear stress at section a-a and percentage difference with average shear…

Q: Q2) cantilever beam is 4 m long and has a distributed load of 300 N/m. The flexural stiffness is 60…

Q: 30 DEGREES. 3 m 2 m 40 KN

Q: Reinforce concrete beams DF, BE, and EH are 318 mm wide and 488 mm deep. The beams support a…

A: Slab dimension = 2.83 m x 7.88 m Column width = 318 mmColumn depth = 488 mmDead Load, DL = 6.83…

Q: 3. A concentrated load of 1200 N operating at the free end of a 6-meter-long steel cantilever beam…

Q: Assume that A = 8° 24’ the station of the PI is 64 + 27.46 and terrain conditions require the…

A: Given - Deflection angle = I = 8°24' Minimum radius = 2864.79 m PI = 64 + 27.46 Assume 20m of…

Question

To develop a shear strength of 375 kN, find the spacing of 10 mm diameter stirrups consisting of 3 legs

Given:
Beam dimensions, b = 350 mm, h = 450 mm
Effective cover to centroid of steel reinforcement = 75 mm
Concrete f'c = 27.5 MPa
Main reinforcement steel, fy = 415 MPa
Stirrups, fyv = 275 MPa
Shear strength reduction factor =0.75
Beam is subjected to shear and flexure only

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given data

VIEW

Step 2 Solution

VIEW

Step 3 Results

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 1m RB B 2m C 153 kN/m 2 m D 28 KN 3m 19 kN/m E RE 2 m Question: Compute the shear diagram of the given load diagram F
Use transformed-area method. The cross section shown consists of a hollow concrete beam with an effective depth of 400 mm. The beam is reinforced with 4 - 16mm diameter bars placed 50 mm from the bottom of the beam. If the beam has a simple span of 6 m, what total uniform load (including its own weight) could the beam carry besides a concentrated load of 8 kN at midspan. Fc' = 7 MPa, fs = 124 MPa, n=12. 75mm 100mm & 75mm 4 D 4 150mm 200mm 50mm 50mm
A reinforced beam of size 300 mm × 450 mm and an effective depth of 400 mm is subjected to a working shear force of 100 kN. The beam is made up of M 25 concrete and Fe 415 steel. Determine the nominal shear stress (N/mm2)
The unsymmetrical built-up section of the given dimensions supports the given load shown. Determine the maximum fv or the beam shear developed in MPa. 10 KN 7 KN 6 KN/m 12 KN/m 1m 3m 2m a
Strength of Materials, i need solutions in 15 minutes please. Q/ The Inverted T section of a L - m simply supported beam has the properties shown in Fig. (4). Find the flange width (b) so that the allowable stresses( σ tension max = 30 Mpa) and (σ compression max. = 90 Mpa.)
Current Attempt in Progress A simply supported wood beam carries a concentrated load of P = 9600 Ibs as shown. The beam spans are L1 = 7 ft and L2 = 14 ft. The rectangular cross section has a width of b = 6.0 in. and a depth of d = 15 in. At section a-a, which is x, = 3 ft to the right of pin support A, determine the magnitude of the horizontal shear stress in the wood beam at point H, which is located yH = 3.5 in. above the centroidal z axis. Ук a L Answer: TH = psi
The design specifications of a 1.2-m-long solid circular transmission shaft require that the angle of twist of the shaft not exceed 4° when a torque of 750 N-m is applied. Determine the required diameter of the shaft, knowing that the shaft is made of a steel with an allowable shearing stress of 90 MPa and a modulus of rigidity of 77.2 GPa. The required diameter of the shaft is mm.
1.) A beam carries the loading shown. Design a rectangular timber beam if the permissible stresses are 120 Mpa in tension and compression, and 100 Mpa in shear. 20 kN/m 50 kN A B 6 m + 2m
A Universal beam of I shaped cross-section is 203 mm deep, and 133 mm wide and has a steel plate 150 mm by 10 mm thick fastened to each flange. Ix-x for the universal beam is 28.80×10^6 mm^4. a) Determine the total uniformity distributed load which may be carried over a simply supported span of 6 metres if the permissible bending stress is 165 N/mm^2. Neglect the self-weight of the beam. [Ans.: 124.02 KN/m] b) Determine the minimum central length over which the additional plates are required. [Ans.: 4.23m]
A simply supported beam spans 8 m. the cross section width is 300mm, the effective depth is 500mm. It is required to carry a uniformly distributed load of 150 kN/m at ULS. Assume fe=30 MPa and fuk=500 MPa. Design the beam for both bending and shear.