To determine the stud spacing (maximum span of the plywood), assuming a uniform load of 712.50 pst what is most nearly the maximum stud spacing? Assume the following: . 3/4" BB-OES plywood is used and oriented in the strong direction 10.50 in. 6.00 in. 8.50 in. O 12.00 in.

Q: 1. EXAMPLE 11.2 Calculate the station of the BC and EC. You are given the following information:…

A: Deflection angle, ∆=12°51'Radius of curve, R=400mThe station of point of intersection, PI=0+241.782

Q: Station A B C Angles 41° 73° 67° No. of Measurement 4 6 2 A. Compute the most probable value of…

A: Weight is inversely proportional to number of observation

Q: Bearing Angle Traverse Given the tabulated measurement of the closed traverse as shown. Determine…

A: Introduction- Leveling is a discipline of engineering that determines the location of an item on the…

Q: From the following measured interior angles of a five sided figure: Station Values of Angles ( No.…

A: To find :

Q: : Find the area of the polygon ABCE (AVE area). Latitude Departure E Line W AB BC 65 80 CD 80 20 DE…

A: SINCE  latitude and departure of line AB is not given we need to find them   In a closed traverse :…

Q: Ø7/8 2 holas R 1.780+0.020 .0.000 0.375t0.002 -0.000 ROCKER ARM %3D

A: How to input units in such a way in Autocad.

Q: 45 67 89 2. lo0 l00 l00 300 b00 Find Po4 FIL assumei= 8%

A: step 1-

Q: Complete the table below. D LINE AB BC CD 118°37 105°22' 108° 28' E AZIMUTH from North B 120°28¹…

A:

Q: ду 5WL3 384EI (5×4369.43722kg x 33m3) 384 х 200GPах 188 × 106 mm

A:

Q: What are the sources of errors and mistakes in fundamentals of surveying?? In essay from please 5-10…

A: Sources of error and mistakes in surveying are as follows :- Instrumental error Natural error…

Q: Write AutoCAD commands for drawing the following figure (without color). Use Relative Polar…

A:

Q: Find x and y

A: We will divide the given C-section into three sections as shown in the figure:

Q: Observed Bearings Length (m) Computed Internal Adjusted Values Line Forward Вack Sta Cor Interior…

A:

Q: A distance of 300 m is to be laid-out using a tape having an incorrect length of 29.98 m. How much…

A: Given, Distance to be measured, say D = 300 m Actual/incorrect length of tape, L' = 29.98 m   To…

Q: Draw projections of the following two points A & B on the same XY line. Keep a gap of 50 mm between…

A: The figure or view shaped by joining, in right succession, the points at which these lines meet the…

Q: view 20mm 30mm 60mm 76.00 mm B 60.00 mm 69.00 mm D 26.00 mm 46.00 mm F 56.00 mm 66.00 mm

A:

Q: Horizontal angle measurement

A: A theodolite is used to measure horizontal as well as vertical angles.  Measurements are taken with…

Q: Find the interior angle B at point 2 inside the baseline of points 1,2 and 3. Please do not write…

A: Given, point y x 1 1512.48 2420.25 2 1550.79 2221.24 3 1570.24 2526.97

Q: LINE BEARING DISTANCE LATITUDE DEPARTURE DEG MIN N (+) S (-) Е (+) w (-) 1-2 S 33 29 w 42.63 35.555…

A: Finding out distance of 3-4 and 4-5 lines.

Q: F 31 ° 58 ° X(+) B=(3.3,0,0) m y(+) Z(+)

A: Given:- A coordinate system is given The coordinates of point B = (3.3,0,0) m  Point A lies on the…

Q: net area along 4,5,2,6,7

A: Given data, Width of the plate= b= 150mm Diameter of the rivet= d0= 20mm Thickness of the plate = t…

Q: hat is the name of the equivalent to the "Y" axis in surveying applications? O North coordinate O…

A:

Q: ∆у = ду 5WL3 384Е (5 ×3758.0698kg x33m3) (384 X200GPa x39.2x106 mm4

A:

Q: May I ask if the answer for this problem is q =11.44? It think the answer key is wrong of otherwise,…

A: You are correct as per the diagram and calculations shown

Q: A surveving transcript of a closed traverse is defined by the vertices ABCDEFGHIJKL. Enor Ace is…

A: Given -

Q: Determine the coordinates of the centroid of the shaded area. 10 E 20 20 10 30 40 20. 65 Dimensjons…

A:

Q: Determine the x- and y-coordinates of the centroid of the shaded area.  Input values in two (2)…

A:

Q: Problem 26.5 Two level sections of 40-m stations with center heights of 1.32 and 1.59 m in cut, base…

A:

Q: 2788.91509^(1.336898)

A: 2788.91509^(1.336898) = 40382.71846

Q: Draw the orthographic Projections of given object.

A:

Q: 9.18 Compute I, and I, for the region shown. 40 mm 40 mm 68 mm 66 mm 66 mm

A:

Q: What is the horizontal distance meg sured in meters ? [NOTE :) AN VWER 3 DE CIM AL EXPRESS YOUR UPTO…

A: To find horizontal distance

Q: How much is the strike separation (i.e., line AB on the map)? Scale: 18mm = 100m 82m 181m 67m 24m O…

A: AB = 32 mm

Q: 18. In Question 16, in analyzing the triangle formed by the closing line and the two courses with…

A:

Q: 3 / 5 \times 11 / 4 \text { inches } \times 3^{1 / 6}

A: To find:- Multiplication

Q: 1. EXAMPLE 11.2 Calculate the station of the BC and EC. You are given the following information: A…

A:

Q: ation tion Military, mining, land development, resource management, hydrography; all these domains…

A: This question is related to the Surveying Engineering from Civil Engineering. In this question ask…

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.