I need all the parts kindly do nearly and correct only Learning Goal:To become familiar with the force method of analysis for axially loaded composite members.As shown, a concrete column is reinforced with four steel bars. The column has length L = 9.00o m snd a radius T = 350.0 Imm The steel bars each have a diameter of d = 29.00 mm, and the magnitude of the applied axial force is P = 1100 kN Assume the plate on top of the column allows for equal distribution ofthe applied force over the entire column and is infinitely rigid. The modulus of elasticity for the concrete is E. = 25.0 GPa and the modulus of elasticity for the steel is E, = 200.00 GPaPart A - Axial force in the concretePart C- Normal stress in the concreteUsing the force method of analysis for axially loaded members, determine the sxial force in the concrete.Using the information obtained about the axial force in the concrete, determine the normal stress in the concrete.Express your answer to four significant figures and include appropriate units.Express your answer to four significant figures and include appropriate units.• View Available Hint(s)> View Available Hint(s)HA??P. = ValueUnitsValueUnitsSubmitSubmitPart B - Axial force in the steelPart D - Normal stress in the steelUsing the force method of analysis for axially loaded members, determine the axial force in the one of the steel bars, P..Using the information obtained about the axial force in one of the steel bars, determine the normal stress in one of the steel bars. (The other three will have the sme normal stress.Express your answer to four significant figures and include appropriate units.Express your answer to four significant figures and include appropriate units.> View Available Hint(s)> View Available Hint(s)HA?P, = ValueUnitsValueUnitsOs =SubmitSubmit

Given: L=9 mradius of concrete member,r=350 mmdiameter of steel rods,d=29 mmP=1100 KNEc=25 GPaEs=200…

To become familiar with the force method of analysis for axially loaded composite members. As shown, a concrete column is reinforced with four steel bars. The column has length I0.000 m and a radius r350.0 mm The steel bars each have a diameter of d 20.00 mm, and the magnitude of the applied axial force is P- 1100 kN Assume the plate on top of the column allows for equal distribution the applied force over the entire column and is infinitely rigid. The modulus of elasticity for the concrete is E. = 25.0 GPa and the modulus of elasticity for the steel is E, 200.00 GPa • Part A- Axial force in the concrete • Part C- Nomal stress in the concrete Using the force method of analysis for axially loaded members. determine the axial force in the concrete. Using the information obtained about the axial force in the concrete, determine the normal stress in the conerete. Express your answer to four significant figures and include appropriate units. Express your answer to four significant figures and include appropriate units. > View Available Hint(s) > View Available Hint(s)

To become familiar with the force method of analysis for axially loaded composite members. As shown, a concrete column is reinforced with four steel bars. The column has length I0.000 m and a radius r350.0 mm The steel bars each have a diameter of d 20.00 mm, and the magnitude of the applied axial force is P- 1100 kN Assume the plate on top of the column allows for equal distribution the applied force over the entire column and is infinitely rigid. The modulus of elasticity for the concrete is E. = 25.0 GPa and the modulus of elasticity for the steel is E, 200.00 GPa • Part A- Axial force in the concrete • Part C- Nomal stress in the concrete Using the force method of analysis for axially loaded members. determine the axial force in the concrete. Using the information obtained about the axial force in the concrete, determine the normal stress in the conerete. Express your answer to four significant figures and include appropriate units. Express your answer to four significant figures and include appropriate units. > View Available Hint(s) > View Available Hint(s)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.4.10P: A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete...

See similar textbooks

Similar questions

A 10-ft rigid bar AB is supported with a vertical translational spring at A and a pin at B. The bar is subjected to a linearly varying distributed load with maximum intensity q0. Calculate the vertical deform at ion of the spring if the spring constant is 4 kips/in.
-11 A rubber cube R of a side L = 3 in. and cross- sectional area A = 9 in2 is compressed inside a steel cube S by a force F = 5 lb that applies uniformly distributed pressure to the rubber. Assume E 0.3ksi and,, = 0.45. (a) Calculate the lateral pressure between the rubber and steel (disregard friction between the rubber and the steel, and assume that the steel block is rigid when compared to the rubber). (b) Calculate the change in volume of the rubber.
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A polyethylene tube (length L) has a cap that when installed compresses a spring (with under-formed length L1) by an amount ?? = (L1 = L). Ignore deformations of the cap and base. Use the force at the base of the spring as the redundant. Use numerical properties given in the boxes. (a) What is the resulting Force-in the spring, Fk? (b) What is the resulting Force in the tube, Ftl (c) What is the filial length of the tube, Lf? (d) What temperature change ?T inside the tube will result in zero force in the spring
A sign of weight W is supported at its base by four bolls anchored in a concrete footing. Wind pressure P acts normal to the surface of the sign; the resultant of the uniform wind pressure is force fat the center of pressure (C.P). The wind force is assumed to create equal shear forces F/4 in the y direction at each boll (see figure parts a and c). The overturning effect of the wind force also causes an uplift force R at bolts A and C and a downward force (— R) al bolts B and D (see figure part b). The resulting effects of the wind and the associated ultimate stresses for each stress condition are normal stress in each boll (h — 60 ksi); shear through the base plate (th = 17 ksi); horizontal shear and bearing on each bolt ( tfur = 25 ksi and cr^ = 75 ksi): and bearing on the bottom washer at B (or D) (abor = 50 ksi).
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
The inclined ladder AB supports a house painter (85 kg) at C and the weight iq = 40 K/m} of the ladder itself. Each ladder rail (t5= 4 mm) is supported by a shoe (ts= 5 mm) that is attached to the ladder rail by a bolt of diameter d = 8 mm
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
Solve the preceding problem for a W 250 × 89 steel column having a length L = 10 m. Let E = 200 GPa.