Throughout the voltage divider experiment a student observes the current never changes as long as the power supply voltage is never changed. They would like to make a plot to determine if the potentiometer is linear with respect to wiper position. Which of the following plots allows for that determination by giving a straight line if the device is linear? All of these plots will give a straight line if the potentiometer is linear. l2 O A plot of V₁ - V₂ (vertical axis) vs (horizontal axis). l₁ O A plot of 2 (vertical axis) vs (horizontal axis). l₁ O A plot of V₁ + V₂ (vertical axis) vs l2 (horizontal axis).

Throughout the voltage divider experiment a student observes the current never changes as long as the power supply voltage is never changed. They would like to make a plot to determine if the potentiometer is linear with respect to wiper position. Which of the following plots allows for that determination by giving a straight line if the device is linear? All of these plots will give a straight line if the potentiometer is linear. l2 O A plot of V₁ - V₂ (vertical axis) vs (horizontal axis). l₁ O A plot of 2 (vertical axis) vs (horizontal axis). l₁ O A plot of V₁ + V₂ (vertical axis) vs l2 (horizontal axis).

Similar questions

Find the total capacitance of the combination of capacitors shown: 5.0 uF 3.5 μF 8.0 uF I 1.5 μF H 0.75 μF 15 μF J Hint: Identify parts of the circuit that are parallel or in series. Replace these parts by their equivalent capacitance. Draw a circuit diagram of the simplified circuit with the equivalent capacitances. Repeat the steps above until you simiplfy the circuit as much as possible. C = HF
Figure R₁ ε # R₂ Z R3 R₁ ▼ Find the following currents. • The current I₁ through the resistor of resistance R₁ = 15.02. • The current I2 through the resistor of resistance R₂ = 45.0 • The current I3 through the resistor of resistance R3 = 20.02. • The current I4 through the resistor of resistance R4 = 25.02. Express your answers in amperes separated by commas. ► View Available Hint(s) I1, I2, I3, I4 = Submit Part D for Palit for Part do for Part redo for art C recerfor Part C keyboard shortcuts for Part C help for Part C Find the following potential differences. • The magnitude of the potential difference AV₁ across the resistor of resistance R₁ = 15.0 S • The magnitude of the potential difference AV₂ across the resistor of resistance R₂ = 45.0 2. • The magnitude of the potential difference AV3 across the resistor of resistance R3 = 20.02. • The magnitude of the potential difference AV4 across the resistor of resistance R4 = 25.02 Express your answers in volts separated by commas.…
Capacitance, Charge and Voltage: Q = CV 1. Click the Reset Button on the bottom right of the PHET simulation. 2. CHECK Plate Charges and Bar Graphs boxes in the upper right so your display resembles the graph below. 3. SET the Plate Area to 200 mm² and the Separation to 4.0 mm. Capactance Tup Pate Charge oc Sured Energy Pu Charges r Graphs O e Fd Cument Direction 1500 V 4. Connect the voltmeter across the capacitor by placing the red on the top plate and black on bottom. If the voltmeter reads a negative, switch the red and black. 5. Set the battery Voltage to 0.25 V. Record the measured plate charge, Q. 6. Repeat Step 5 for each Voltage in Table 3. Table 3: Charge and Voltage Voltage |(V) Plate Charge |(pC) 0.25 V 0.50 V 0.75 V 1.00 V 1.25 V 1.50 V
The voltage V (volts), current I (amperes), andresistance R (ohms) of an electric circuitare related by the equation V = IR. Suppose that V is increasing atthe rate of 1 volt/sec while I is decreasing at the rate of 1/3 amp/sec. Let t denote time in seconds. What is the value of dI/dt?
Find the slope for each I - V curves in Plot 1. Determine the value of resistances R1 and R2 by using the slope of the I - V curves. Show your calculations. Supply Voltage (Vs) Voltage across R₁__(V₁) Voltage across R₂ (V₂) Current through R₁_(l₁) Current through R₂_(1₂) Computed value of I₁R₁ Computed value of I2R2 2.0 V 1.375v 0.623v 0.6147mA 0.6147mA 1.331v 0.603v Table 4 4.0 V 2.7529v 1.1468v 1.268mA 1.268mA 2.749v 1.245v 6.0 V 4.127v 1.870v 1.901mA 1.901mA 4.121v 1.867v 8.0 V 5.503v 2.493v 2.536mA 2.536mA 5.498 v 2.490v 10.0 V 6.878 3.118v 3.171mA 3.171mA 6.874v 3.114v Current 3.5 3 in 2.5 2 1.5 1 0.5 0 0 2 Plot 1: I-V curves for resistors R1 and R2 using the data from Table 4 4 Voltage 6 8 Current 3.5 3 2.5 2 1.5 1 0.5 0 0 0.5 1 1.5 Voltage 2 2.5 3 3.5
A car battery is rated at 600 AH (i.e., amps x hours). Calculate the number of coulombs this is equivalent to.
For the image given, determine the power of the current source. Include whether it is supplying or absorbing power. Please explain clearly and give the answer to P1A .
The equation for the graph is y= x^2 Resistance = (Voltage/Current), however I don't think that would work in this case as it is not a linear graph. It might have something to do with the equation but i'm not sure Don't use chat gpt It Chatgpt means downvote