Three uniform disks made up of two same materials with one being lighter compared to the other material. The inner half of the disk 2 is made up of the denser material while for the other two disks it makes the outer half. Tangential forces of equal magnitude are applied either on the interface of inner and outer half or on the outer edge. Write the disk numbers from highest to lowest according to: (a) the torque about the disk center (b) the rotational inertia about the disk center (c) the angular acceleration of the disk

Q: piece of metal subjected to three forces is fold as shown in the figure. Replace the three forces…

A:

Q: Draw the Free-body diagram in the image below of POINT A, and  accurately label everything.…

A:

Q: Solve the statics problem shown here by calculating the X-direction and Y-direction forces at points…

A:

Q: I can't find C or D

A: Draw the free-body diagram.

Q: 18 in. В 20 in. 80 lb 24 in. 24 in. y 38 in. D PE 20 in.

A: make FBD for the given figure

Q: 5. Dak Prescott has a mass of 107 kg and is 25 years old. Calculate the total moment of inertia for…

A:

Q: kg ånd thE the moment of intertia about Z axis.

A: calculate the mass moment of inertia about z axis at a distance x=0.4

Q: For the beam I-section below, calculate the second moment of area about its centroidal x-axis…

A:

Q: What is the position of the center of mass of the bar, measured as distance x from the bar's left…

A:

Q: Find the tension force in each 35 cabler 木 oss kg.

A:

Q: 3.1 3.2 Determine the location of the centroid for the cross-section shown below and draw a scaled…

A:

Q: Q: A four masses A, B, C and D have attached to rotating shaft. The weigh of each mass is 160, 260,…

A:

Q: A hollow mast of circular section as shown is to be stiffened by bonding two strips of the same…

A: Find the value of h.

Q: g x direction. The initial strain along y direction. The initial strain in z direction Additional…

A: Rectangular steel block  Lx = 3 inchLy = 2 inchLz = 4 inch Fx = + 30 kipsFy = -60 kipsFz = 54 kips

Q: Find the mass of a cylindrical solid x+y = 36 of height 5 and radius 6. Assume that its density is…

A:

Q: The wheels of a wag 5.08 kg, and two th ta = 0.0462 m thic moment of inertia

A: The mass moment of inertia of the wagon wheel can be determined as,

Q: The figure above shows a uniform rectangular lamina OQRS, where OQ = 4a and QR a. A sector OPS of…

A: Given that, The centroid of the rectangle and sector can be given as, The sector of the quarter…

Q: A bar 2 m long makes an angle of 30° with the horizontal. A force of 40 N is applied 0.4 m from the…

A:

Q: A rectangular aluminum block having a dimension of (from origin) for the +250 mm along the Y-axis,…

A: Given: The dimension along the y-axis is 250 mm. The dimension along the x-axis is 100 mm The…

Q: OD 3m 16 my 2 m Figure 3

A:

Q: Find the centroid of the shaded area about given axis. Figure: 1a and Figure: 1b

A: Note: As per policy, from multiple questions we can solve first one only.

Q: Determine the angle θ (degrees).

A:

Q: 1. You are tasked to design a shaft for power transmission through a belt and pully at its right…

A: Given:To find:

Q: The hook is used to lift the force of P as shown. The section dimensions of a-a is given: P = 40 kN…

A: Given data: ◆ Load applied: P = 40 kN ◆ Inner radius of hook: c = 70 mm ◆ Parallel sides of section:…

Q: Calculate forces (moments if applicable) for all points shown and write them down in a table.

A:

Q: YA In the bracket Shown in figure GI . 60ON %3D im, 60° 03 = 3 kg). Find the resultant R of the…

A: The free-body diagram of the bracket is given by,

Q: A machine component is subjected to the forces and couples shown. The component is to be held in…

A:

Q: A machine part as shown in following figure consists of three disks linked by light weight struts.…

A:

Q: I want the force for A and B by using the centroid or solve it by the right way

A:

Q: splacements and reaction

A:

Q: Parameter A=0 B=7 C= 7 D= 3 E=7 P = 700 + 73 = 773 0 = 30 + (37) x 0.1 = 33.7° Note: Figures CDFE…

A:

Q: 1. Four pulleys are attached to the 55 mm diameter steel shaft. If torques is applied to the pulleys…

A: Given data: The diameter of the shaft, d=55 mm. Refer to the table "properties of steel: to the…

Q: What is the moment of inertia of the object about an axis at the left end of the rod? kg-m2    2)…

A: Given: mr=6.86 kgL=5.76 mms=5mr=34.3 kgR=1.44 mL=4RF=463 N To determine: The moment of inertia of…

Q: consider the rotational axis at the point where the tire contacts the ground, directed perpendicular…

A: A man is pulling a wheelbarrow to lift the weight. A wheelbarrow is a vehicle to lift weight…

Q: The 1 inch diameter shaft is subjected to the loads shown. Draw the "loading diagram" showing the…

A: Diameter of shaft, d = 1 inch.There are 3 forces acting on the beam, 100 lb, 75lb, 80lb.

Q: With the elbow flexed 30 degrees, the moment arm of the biceps is equal to 10 mm. Solve for the…

A:

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.