Three types of pin fins. The fins will be subjected to a gas in cross flow at v= 10 m/s. The cylindrical fin has a diameter of D = 20 mm, and cross-sectional area is the same for each configuration shown in the sketch. V, T, V, T. V, T Configuration A Configuration B Configuration C For fins of equal length and therefore equal mass, which fin has largest heat transf rate? Assume the gas properties are those at T (treat it as air) = 350 K. Hint: Assume the fin can be treated as infinitely long.

Three types of pin fins. The fins will be subjected to a gas in cross flow at v= 10 m/s. The cylindrical fin has a diameter of D = 20 mm, and cross-sectional area is the same for each configuration shown in the sketch. V, T, V, T. V, T Configuration A Configuration B Configuration C For fins of equal length and therefore equal mass, which fin has largest heat transf rate? Assume the gas properties are those at T (treat it as air) = 350 K. Hint: Assume the fin can be treated as infinitely long.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A velocity of the cylindrical particles of diameter and length are 0.3 mm. It is drop in the air tube .The density of the particle is 1200 kg/m³. The initial velocity of the particle is zero. Air conditions are 28 °C and 1 atm. The viscosity of air is 1.8 x 105 kg/m-s, and superficial velocity of air is 11 m/s. The Reynolds number range is between 1100 and 900. (a) Derive an equation of the velocity of the particles with neglect wall effects. (b) How long of distance if the velocity become steady state filling?
Consider a thin-walled, ﬁ xed-volume container of volume V that holds an ideal gas at constant temperature T. It can be shown by dimensional analysis that the number of particles striking the walls of the container per unit area per unit time is given by nv-/4, where as usual n is the particle number density. The container has a small hole of area A in its surface through which the gas can leak slowly. Assume that A is much less than the surface area of the container. (a) Assuming that the pressure inside the container is much greater than the outside pressure (so that no gas will leak from the outside back in), estimate the time it will take for the pressure inside to drop to half the initial value. Your answer should contain A, V, and the mean molecular speed v-. (b) Obtain a numerical result for a spherical container with a diameter of 40 cm containing air at 293 K, if there is a circular hole of diameter 1.0 mm in the surface.
2. A large sheet of glass 2” thick is initially at 300oF throughout. It is plunged into a stream of running water having a temperature of 60oF. How long will it take to cool the glass to an average temperature of 100oF. For glass k = 0.40BTU/ft-hroF, ρ = 155 lb/ft3 and Cp = 0.20 BTU/lboF.
A 1-in-diameter (D = 1 inch) rotating machined shaft has a groove 0.1-in deep with a 0.1-in radius machined into it. The shaft is subjected to a pulsating (i.e. R = 0) torque and bending moment of following values. Based on laboratory experiments at 550°F, Sut = 150 ksi, Sy = 120 ksi, and S'e = 90 ksi are measured. Using mod-Goodman equation and for operating temperature of 550°F and 90% reliability, determine the factor of safety for yielding and fatigue of this shaft. Tmax = 2000 Ib-in Mmax = 1600 lb-in Mmin = -1200 Ib-in D - -d- M T M T
Information Momentum Balance
What is mechanical pressure Pm, and how is it used in an incompressible flow solution?
A plate is cooled by a fluid with Prandtl number Pr >> 1. Surface temperature varies with distance form the leading edge according to where C is constant. For such a fluid it is reasonable to assume that axial velocity within the thermal boundary layer is linear given by u=V% y Determine the local Nusselt number and show that surface heat flux is uniform. Use a third degree polynomial temperature profile and assume laminar boundary layer flow y YA To Vo T₁(x,0)=T +C√√x U -8 &₁ X T₁(x) = T₁ +C√x
i need the answer quickly
subject (fluid mech 2) pls show me full steps sir with clear handwriting pls answer me withi 30 min sir