Three pipes of 400 mm, 350 mm and 300 mm diameter are connected in series between two reservoirs with a difference in level of 12 m. The friction factors are 0.024, 0.021 and 0.019 respectively. The lengths are 200 m, 300m and 250 m respectively.  a.) Find the flow in m^3/s in PIPE 3. b.) What is the head loss in meters in pipe 3? c.) Determine the length of an equivalent 350 mm diameter pipe

Q: 1-The storage tank shown below is to be used to supply a community such that the pressure at Point B…

A: Q= ,  , D = 600mm=0.6m , L = 1000mTo Determine: Water Depth(h) in the tank that will meet the design…

Q: Two tanks with a difference in water levels of 180 m are shown in Figure Q4. The tanks are connected…

A:

Q: Two tanks A and B have 80 m difference in water levels, and are connected by a pipe 0.3 m diameter…

A: Friction factor f = 4F = 4×.002 = .008 Total inflow = Total net flow at junction CQ1 = Q2 + Q3Q1 =…

Q: A single pipe of length 1500mand diameter 60 cm connects two reservoirs having a difference of 20 m…

A:

Q: Piezometric tubes are tapped into a pipe section as shown in the figure below. The liquid is…

A:

Q: 1) A concrete lined irrigation channel with Manning’s n = 0.020 is needed to convey 12.5 m3/s of…

A:

Q: Tank A has an elevation of 100 m and Tank B has an elevation of 160 m. Since Tank A is lower than B,…

A: Tank A elevation = 100 m Tank B elevation = 160 m Discharge in the pipe (Q) = 0.65 m3/s pipe length…

Q: Two reservoirs 1500 m apart have a water surface elevation difference of 18 m. A cast iron pipe with…

A:

Q: 3. For the system shown below compute the a. Flow rate, (k = 1.1m/day) Pore pressure at point B b. 3…

A: Given Data  Find 1. Flow rate, when K = 1.1 m/day 2. Pore pressure at point B.

Q: The pressure at point 2 shown in Figure is not to fall below 4.14 Bar when the flowrate from the…

A:

Q: Pressurised water flows through two connected circular pipes as shown in Figure 1. Location 1 is at…

A: Given: Discharge  Diameter  Elevation difference  To find: Headloss between two sections Note : Z1 =…

Q: A

A:

Q: Hydraulics equation

A:

Q: 6.88m. Darcy-Weisbach friction factor for all pipes, f=0.0238.    Pipe 1: Length=3500m…

A:

Q: 1. A Venturi tube, as shown in the figure, is used to measure the flow of kerosene runoff (d =…

A:

Q: Three pipes, Pipe A of 300 m and 30 cm diameter followed by Pipe B of 150 m and 20 cm diameter…

A: The difference in the elevation of the two reservoirs, h = 10m Pipe Length, m Diameter, cm…

Q: Water flows from the tank shown in the figure below. At a depth of 1.5 ft the rate of change of…

A:

Q: QUESTION 2) Pump gives 20 m of head to the flow (H, = 20 m). Neglect all kinds of minor %3D losses.…

A: For pipe I: The pressure head available= Head losses due to frictional+ value.…

Q: The specific energy, E, is defined as the total energy head with respect to the channel or pipe…

A: Given data : Flow rate (Q)=1 m3/sWidth (w)=5 mDepth (d)=20 cm

Q: A faucet is connected at the end of a pipe of roughness .00026. The pipe connected the faucet to the…

A: Given - Roughness = 0.00026 Pipe is connected to the water main, 40m away and 1.2m away. The…

Q: The pressure heads are measured at two sections in a pipeline and are found to be 8.3 m at point A…

A: Step 1: Step 2: Step 3: Step 4:

Q: 1. Four reservoirs are connected as shown below. Minor losses can be ignored. Determine the flow…

A: Four reservoirs are connected as shown in the figure.Coefficient of friction, f = 0.02Pipes Length…

Q: Read the question carefully and give me right solution according to the question

A:

Q: Two tanks A and B have 80 m difforence in water levels, and are connected by a pipe 0.3 m diameter…

A: area    A=π4×d2=π4×0.32=0.07065 m2and friction loss for first half pipe length  hf1=8fQ12L2π2gD5and…

Q: Pipe in Series: Consider the two reservoirs show in below figure, connected by a single pipe that…

A: Z1-Z2= 9 mD1= 200 mmD2= 250 mmL1= 15 mL2= 45 mKLen= 0.5KLex= 1f= 0.01

Q: Fluid

A: Given data- Total length (L) = 3000ft Head loss(h) = 20ft Height sand(H) = 20ft Width of sand (B) =…

Q: Problem 3 A reservoir with water is pressurized as shown. The pipe diameter is 1 in. The head loss…

A: Detailed solution is given below, still if you have any query please feel free to contact me.Thanks…

Q: A 2 B 1 The three-reservoir system is shown below: 3 |C The elevation of Reservoir at A is 140m and…

A:

Q: 5. Determine the pressure head elevations at B and D and the discharges in the branches in the…

A: From question length and diameter of each pipe is given.Roughness coefficient of each…

Q: A pipeline 300 m long discharge freely at a point 50 m lower than the water surface at intake…

A: Given :

Q: For the piping system shown below, determine the flow distribution and the piezometric heads at the…

A:

Q: Determine the flow in each pipe in the reservoir shown below. Use the values provided in the table.…

A: To Determine the flow in each pipe in the reservoir shown.

Q: Oil flows through a 200 mm diameter horizontal cast iron pipe (friction factor f = 0.0225) of length…

A: Given data- Diameter D=200 mm =0.2 m, Friction factor f=0.0225, Length L=500 m, Flow Q=0.32 m3/s,…

Q: b) Figure Q2 (b) shows the water piping system from reservoir A to reservoir B. The water level for…

A:

Q: A pipe, 40 m long, is connected to a water tank at one end and flows freely in atmosphere at the…

A:

Q: A vertical pipe system shown in the Figure below, d = 300 mm throughout, carries 0.82 (m³/s) of…

A: ###Calculation of pressure drop between A and B when B is 100 m higher than A in Given pipe system…

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?