Three pipes A, B, and C at the same level connected by a multiple differential manometer shows the readings as shown in figure (1). 1.Find the Differential of pressure heads in terms of water column between A and B, between A and C, and between B and C. 2. If pipe A is empty of water, what are the differential of pressure heads? 3. If pipe B is empty of water, what are the differential of pressure heads? 4. If pipe C is empty of water, what are the differential of pressure heads? 5. If all pipes are empty of water, what are the differential of pressure heads? Water 130 cm

Three pipes A, B, and C at the same level connected by a multiple differential manometer shows the readings as shown in figure (1). 1.Find the Differential of pressure heads in terms of water column between A and B, between A and C, and between B and C. 2. If pipe A is empty of water, what are the differential of pressure heads? 3. If pipe B is empty of water, what are the differential of pressure heads? 4. If pipe C is empty of water, what are the differential of pressure heads? 5. If all pipes are empty of water, what are the differential of pressure heads? Water 130 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pump system is used to move water at a flow rate of 30 L/s from a lower to a higher reservoir in a city with an elevation of 1000 m above sea level. The system is shown schematically in the figure below, with ∆?=30 m. Both the suction and delivery pipes have a diameter of 150 mm and an absolute roughness of 0.3 mm. The lengths of the suction and delivery pipes are 6 and 500 m respectively. Ignore local losses and assume a temperature of 15 °C. a)Develop a mathematical expression for the system curve (i.e. the pumping head required as a function of the system flow rate) from basic principles. Name all mechanics principles implemented. b)Calculate the required pump working point. What is the flow regime of the pipe flow. c)What power does the pump add to the water in the system?
A fluid of specific gravity 0.8 is flowing in a pipe. The pressure drop across a flow secti between 1 and 2 is measured by a differential manometer as shown in the figure below The manometric fluid is mercury (S = 13.6). The pressure drop is Fluid (5-0.8) 2 m 0.5 m He Assume density of water is 1000 kg/m³ and g = 9.81 m/s².
Question 4 Quèstion 4 1 points Application of orificemeter is O 1. Measure pressure difference O 2. Measure mass flow rate O 3. Measure pressure difference O 4. Measure volume flow rate
A docs.google.com/forms/d/e/1FAlpQLSetk8UE/ PROBLEM 6: A gasoline line is connected to a pressure gage through a double-U manometer, as shown. If the reading of the pressure gage is 260 kPa, determine the gage pressure of the gasoline line. Assume the density of air to be 1.225 kg/m3 * Oil SG = 0.79 P gage = 260 kPa Gasoline SG= 0.70 Pipe Air 45 cm 50 cm 22 cm 10 cm Mercury SG= 13.6 Water Your answer
During a hydraulics laboratory experiment using a venturi meter and orifice meter to calculate the coefficient of discharge, the following results were obtained. Using the following data produce the results table from the lab results and data given. Table of Results 1 2 3 4 5 HV = (h1 - h2) m HO = (h6 – h7) m Q m3/s HV1/2 HO1/2
Question 3:- A tank with 100.58 kPa pressure is connected with manometer to measure the pressure. The specific gravity of fluid was 0.85 and the atmospheric pressure is 96 kPa find the manometer column height "h". Pam = 96 kPa P=100.58 kPa h=? SG = 0.85
The figure belows shows a closed tank holding air and oil to which is connected a U-tube mercury manometer and a pressure gage, with L₁ = 3 ft, L₂ = 0.5 ft, and L3= 1.25 ft. The densities of the oil and mercury are 55 and 845, respectively, each in lb/ft³. Let g = 32.2 ft/s². Pgage = i Pressure gage lbf/in.2 Air Determine the reading of the pressure gage, in lbf/in.2 (gage). Oil (p=55 lb/ft³) Pam Mercury (p=845 lb/ft³) g=32.2 ft/s²
Problem 2: Manometer and Pipe S = 0.8 300 mm dia Water flows past a manometer as shown. The manometer fluid is oil with s = 0.8. If the manometer reading Rm= h = 0.12 m, what is the water velocity at the centerline of the pipe?
Consider oil flowing through a horizontal pipe at a rate of 3 liter/s. There are two sections of the pipe with diameters 10 cm and 7 cm and the two sections are connected by a smooth reducing section as shown in the schematic. We use a manometer with glycerin as the manometer fluid (with glycerin density of Pglycerin 1,260 kg/m³) to measure the pressure difference between the two pipe sections. Assume that frictional effects are negligible and consider specific gravity of oil as SGoil = 0.76. What is the manometer reading, h (i.e. differential height of glycerin between the two arms of the manometer)? 10 cm I h T 7 cm-
Topic: Flow in closed conduits For the pipe network shown, the flow of water from A to the first junction is 2 cubic feet per second. Assuming all pipes have a friction factor of 0.020 Which of the following statements is FALSE? *The inflow in pipe 1 is equal to the ouflow in pipe 5. *The sum of the discharge of pipes 2 and 4 is equal to the ouflow in pipe 5. *The sum of the discharge of pipes 2 and 3 is equal to the inflow as well as the outflow. *The inflow in pipe 1 is equal to the outflow in pipe 5 Please answer with complete and detailed solution. ASAP. Thank you
Water is flowing through a venturimeter shown. The difference in pressure between Point 1 (D = 4cm) and Point 2 (D = 2cm) is measured using open tubes. If h is 50cm, solve the volumetric flowrate. h 下 O 0.00110m^3/s O 0.00162m^3/s O 0.00254m^3/s O 0.00102m^3/s
Please show complete answers and complete solution. Use the general solution for solving the problem. Answer neatly!