Three loads A, B, and C are connected in parallel across a 1.5-kV-rms 60-Hz Source, as show below. Load A consumes 10 kW with a 90 percent lagging power factor. Load B has an apparent power of 15 kVA with an 80 percent lagging power factor. Load C consumes 12 KW with a 70 percent lagging power factor. Find the power, reactive power, and apparent power delivered by the source. What is the power factor seen by the source? State whether it is leading or lagging. Source A B

Three loads A, B, and C are connected in parallel across a 1.5-kV-rms 60-Hz Source, as show below. Load A consumes 10 kW with a 90 percent lagging power factor. Load B has an apparent power of 15 kVA with an 80 percent lagging power factor. Load C consumes 12 KW with a 70 percent lagging power factor. Find the power, reactive power, and apparent power delivered by the source. What is the power factor seen by the source? State whether it is leading or lagging. Source A B

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Write a report to compare between Ac Through capacitance and AC through in inductance then: For the circuit shown beside, find The average power delivered to the * .circuit jón a 1000 v 82 -j72 b
Draw the power factor triangle showing the different labelled sides. Illustrate a lagging power factor using a sinusoidal waveform. (d) List 2 negative effects of a poor power factor (e) How can a lagging power factor be corrected?
Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average and RMS for both currents. ot io Vs = 220V a = 220° + ot 1002
A load is connected across a 25,000 Volts, 60 Hz source and draws a current of 90 A rms. If the power factor of the load is to be corrected from 0.75 lagging to 0.9 lagging, find the capacitance of the capacitor to be connected in parallel with the load.
Q2: Write a lecture for teaching the complex power fed to an (R-L) load fed from an AC power source of sinusoidal voltage and current waveforms, describing its three components, their waveforms, their power triangle, and units.
A current of 10 A rms flows when a single-phasecircuit is placed across a 220-V rms source. Thecurrent lags the voltage by 60◦. Find the powerdissipated by the circuit and the power factor.
A source delivers 50-kVA to a load with a power factor of 65percent lagging. Find the load’s average and reactive powers.
2. A voltage applied to a load is V=208 4 20°V and current through load is I=10 a–10° A. Find the following [SO 1] o complex power consumed by load o Is the load inductive or capacitive? o the power factor of the load o the reactive power consumed or generated by the load. o Does the load consume or supply reactive power?
Two load connected in parallel supplied by 480-V. The first load absorbs 2kVA at 0.5 lagging power factor and the other load absorbs 4kVA at 0.6 leading power factor. Find the total impedance and the rms source current
How about the average power on each elements? And is it absorbing or delivering power too?
Consider the circuit shown in Figure 1. V1 is a 7.2 kHz sine wave with an amplitude of 4 V.Figure 1: RC Circuit Schematic1. Determine the total impedance (Z) of the circuit.2. Using V1 as a zero-phase reference, calculate the values of the following:a) Amplitude and phase of current (I)b) Amplitude and phase of voltage across R1 (VR1)c) Amplitude and phase of voltage across C1 (VC1
A load has a leading power factor. a) Is it a capacitive or inductive load? b) Is the reactive power positive or negative? c) Repeat for a load with lagging power factor