Three bars pinned together at B and C and supported by hinges at A and Das shown in Figure 1, form a four-link mechanism. Determine the Forces at BC. * 300 lb FIGURE 1 321.237 Ib

Q: For the figure shown, if P = 50 kN and the vertical movement of end C is limited to 4 mm, then the…

A: Option -- 1250 mm2

Q: Construct a truth table for [(M - J) A (J-S)) - (M-S)

A:

Q: The parameter COD is: O a. Usually less in value than the ulitmate BOD b. Usually equal in value to…

A: The parameter COD is: a. Usually less in value than the ulitmate BODb. Usually equal in value to…

Q: نقطة واحدة What will be the variation in BMD for the diagram? [Assume 10 KN A B .L = 2m] Square O…

A: Step 1: The correct option is: Triangular Here's why:Square: A square beam with uniform load will…

Q: Q2: - A tape 100m long. it's cross sectional area in 0.0585 cm, the apparent length of which was…

A: Length L = 1500 m = 150000 cm Area A = 0.0585 cm2 Standardised pull Ps = 6.75 kg Actual Pull P =…

Q: - the upper part in fig below is a steel and lower part is a cast iron , the load P shortens the…

A:

Q: for part b, what happened to the t on the cty when integrating, can you please show this work again?

A: Given: u = A(1+bt) , v = cty  Required: To explain the stream line equation done in step 2 by the…

Q: Figure 50 mm 150 mm 150 mm 300 mm 1 of 1 Locate the centroid y of the bea Express your answer to…

A:

Q: COMPLETE THE STATEMENTS BELOW. TYPE YOUR ANSWERS IN THE BOX. Refer to the figure shown. Given a…

A: Given Data Determine  1. In collapse-2, Y1 = ? θ 2. In collapse-2, Y2 = ? θ  3. In collapse-2, Y2…

Q: Find the centroid of channel shown in figure T 100 mm K > K C B F 80 mm -10 mm G H 10 mm A T 50 mm -…

A:

Q: Slope deflection to determine the forces reactions

A: Sign convention : assuming clockwise moments as positive(+) and anti-clockwise moments as…

Q: Solve for: [D"C]E a. b. 5АВ - ЗС 4 1 .?

A:

Q: Problem 6.2. The undeformed and deformed outline of a material element are as shown in the figure…

A: Solution: From the Figure given:

Q: The railroad I-beam has dimensions as shown below. In reviewing these old designs, you have been…

A:

Q: ate the computational degrees of free system. LL F H B E D types of

A:

Q: Question 7 7.Value of shear at midspan in Ib. b=3.17 inches h=5.62 inches P= 1657 lb A= 3.75 ft B=…

A: Question is based on the simply supported beam subjected to point load .Magnitude of load and span…

Q: what is design strength. The material of the steel is SM275 and the size is 22mm. The sectional area…

A: Tensile Strength : Tensile means "competent of being drawn out or stretched." Steel's tensile…

Q: Q6• For figure below, caleulate the forces Surfaces on A f B. surface 8 (area = o-1m²) 0.1 air 2 w…

A:

Q: Solve for the centroid of the figure relative to the bottom fiber. You'll be solving only for the y…

A: Unsystematic section is given and it has been asked to determine centroid of y axis. Please refer…

Q: QI (a) A plane element is subjected to a set of stresses as shown in Figure Q1. (i) Determine the…

A:

Q: Find the values that make the equation true. a -6 9 -4 b-3 4 7 C. -1 -9 f d 5 2. -1 e -6 Enter you…

A:

Q: Find the NA here:

A:

Q: Determine the stability and determinacy b b+r = 2j ANAMAN N Classification

A: b + r = 2j ( statically Determinate ) b + r > 2j ( statically Indeterminate ) b + r < 2j (…

Q: 5- What should be the maximum value of cant excess on Broad gauge? a. 65mm b. 75mm c. 92mm d. 100mm…

A:

Q: * = pw 2 gm/cm3 1 gm/cm³ O 4 gm/cm³ O 3 gm/cm³ ОООС

A: 1 g/cm3

Q: ) Prove that stroctare is salee I Stakicalle dotaminate

A: Since the question number to be solved is not specified, the solution for subpart a is as follows:…

Q: The typical units of Cc and Cr are: O Ib/ft? and kPa O Ib/ft and kN/m3 O inches or milimeters O…

A: step 1-

Q: Deter mine the vatation atprint sf the frame shown in figuve. Take E: 20010 mpa 1=30 lo mm4 SEN…

A:

Q: y Ball and sockets 12 D X1 5 X2 E Y1 Z2 z1

A: Step 1

Q: Find Fx

A: ###Determination of Force on orifice in X direction  is Fx =?####

Q: Explain the difference between S, and o

A: Difference between sx , and σ :- The distinction between the sigma (σ) and 'sx' as generally…

Q: Explain withe help of Steps Of X to find the value the sesisting 'F" dusing fos un Ais plane be…

A: Dimensional analysis - To develop a functional relationship between the variable.  modal and…

Q: Explain the following terms used in GMS. a. IBOUND b. HANI c. RCH d. SY e. SS

A: IBOUNDHANIRCHSYSS

Q: 0.5 EI mm S=10 40 EI -5 2 E = 2.1+ 10 N/m² I=70,000 cm4 √ = 10 mm a EJ 2EI b At = 10°c h t = 20%…

A: The given structure is a beam with a span of 2 meters, supported at both ends. The beam has a…

Q: Question 1) F=22 kN single load, M-24 kN.m moment and w=5 kN/m distributed load act on the beam…

A:

Q: Consider a 135-mm-long segment of a simply supported bear. The internal bending moments on the left…

A: Given Data:Internal B.M=75kNm and 83 kNmAssume:b1=120mmb2=45mmb3=210mmd1=75mmd2=175mmd3=75mmTo…