This question about Sanitary Engineering Note: Assume any missing information. Question: Design a rectangular sedimentation tank for a population of one million people. Given the rate of water supply is 150 lit/no/day. Water will stay for 2 hours. (detention period).

Q: Draw a schematic flow diagram showing processes to treat: (a) Groundwater containing dissolved…

A: (a) Groundwater containing dissolved solids of about 2200 mg/L with hardness around 250mg/L as…

Q: 39 286 7.900 Determine the possible flow into MH DI from the WWS piping in Chesapeake Bay, which is…

A: Total sewage flow per person = 1200 L/day / 3.1 = 387.1 L/day/personTotal flow into MIH DI ≈…

Q: Please answer the quesiton in the picture, make sure to show all of your work and provide the…

A: Step 1: Schematic of the Water BudgetPrecipitation (P): 3.20 inchesEvaporation (E): 0.25…

Q: 26. An Extended Aeration treatment plant consists of an aeration compartment with a volume of 1320…

A: Calculate the F/M ratio and the volumetric loading.?

Q: Question 8 Given the following dissolved oxygen data for an aeration test with Cs = 9 mg/L, the KLa…

A: When a supersaturated solution is to be degassed or removal of gas takes place,then equation can be…

Q: Given the data below, design a section of sanitary sewer to carry these flows at a minimum velocity…

A: minimum velocity of 0.6 m/s, n=0.013 minimum cover above the sewer pipe is 1.5m

Q: Subject Environmental Engineering Please answer question 1-6

A:

Q: pare the positive and negative effects of disinfection of wastew

A: Introduction- Wastewater experts will become familiar with the aces, cons, and expenses of different…

Q: Wastewater flow in a sewer can be estimated by adding a known amount of tracer such as salt solution…

A:

Q: You have been selected to design a sewer system for a town of 15000 people. If the average domestic…

A: The following design flow of the sewer is estimated by considering flow from domestic sewage only.

Q: Problem 3: You are considering three design alternatives for treating a pollutant in wastewater…

A:

Q: treatment plant with an average flow of 2.5 m³/s treats its water with alum (Al2(SO4)3 18H2O) at a…

A: Alum dose = 20 mg/LInitial organic matter concentration =Final organic matter concentration = 6…

Q: For the storm sewer system shown below, determine the required diameter of the sewers; extended from…

A:

Q: Problem 3: You are considering three design alternatives for treating a pollutant in wastewater…

A: Given data, Q = 8.6 mgd = 8.6×10^6 gal/d V = 9000 gal. For each system K= 1.1/min for first order =…

Q: 1) Chlorine contact tank (Wastewater Treatment) An activated sludge plant has a design flow (average…

A: Given: The average flow rate is 11 MGD. The depth of the tank is 10 ft. The relation between length…

Q: A rapid sand filter unit has to supply 40 million litres of water per day. 4% of filtered water is…

A:

Q: Determine the footprint area (in ft²) needed for a proposed primary clarifier at a wastewater…

A:

Q: This is a cross-section of a groundwater situation. Label the location of the: Zone of Saturation,…

A: Zone of saturation- A saturated zone is a zone in which all the pores or void in soil mass or rock…

Integrated Solid Waste Management

Integrated Solid Waste Management (ISWM) is a thorough waste suppression, compost, removal and recycling Program. An effective ISWM system considers how to suppress, manage and recycle solid waste in a manner that is most efficiently to protect human health and the surrounding. ISWM system requires evaluation of public wants and demands and then selecting and merging the most effective waste management activities for the proposed demands. The main ISWM activities for solid waste management are Waste prevention, Recycling and Composting, and Combustion and Removal and waste collection in a properly planned, constructed, managed and mitigated landfill areas. Each of these requires careful designing, financing, accumulation, and delivery of activities.