This is a drawbridge, held in place by a cable. The hinge is frictionless. use American units: weight and other forces are in pounds, and torque is in pound-feet. Calculate the torque (positive number) on the drawbridge due to its weight, in Ib*ft. (Use the hinge as your axis.)

This is a drawbridge, held in place by a cable. The hinge is frictionless. use American units: weight and other forces are in pounds, and torque is in pound-feet. Calculate the torque (positive number) on the drawbridge due to its weight, in Ib*ft. (Use the hinge as your axis.)

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A woman applies a torque to a nut with a wrench 0.250 m long. Because of the cramped space, she must exert a force upward at an angle of 70.0° with respect to a line from the nut through the end of the wrench. If the force she exerts has magnitude 46.0 N, what magnitude torque (in N · m) does she apply to the nut? (Assume that the force is applied at the end of the wrench.)
Write the necessary equation of the object shown in figure below. Fx R, go Take the origin of the torque equation about an axis perpendicular to the page through the point O. (Let counterclockwise torque be positive and let forces to the right and up be positive. Use any variable or symbol stated above along with the following as necessary: Fg for the magnitude of Fg.) ΣFx X. = 0 EFy = = 0 Στ = 0
For two existing torques, what third force at a given distance from the pivot will balance them? Imagine a meter stick set up as in the figure. It hangs from a central bracket, and two hanging masses can hang from it from each of their brackets. At a third location, a force probe can either pull up or pull down on the stick, depending on what is needed to balance the stick. The mass of the meter stick is 120 g. sketch the situation (drawing r1, r2, r3, F1, F2, and F3) and determine the magnitude (value) and direction (+ or -) of each torque. Don't include the mass of a bracket that would hold the hanging mass in place; assume the mass listed is the entire mass hanging at that point. For each trial, use the principle of equilibrium (where the sum of torques is zero) to calculate the third, unknown force acting at x3
When tightening a bolt, you push perpendicularly on a wrench with a force of 161 N at a distance of 0.134 m from the center of the bolt. How much torque are you exerting in newton meters (relative to the center of the bolt)? (Enter the magnitude.)
Two blocks, each of mass 2 kg are suspendedfrom the ends of a rigid massless rod of lengthL. The rod is held horizontally on the fulcrumand then released. The length L1 is 15 cm andthe length L2 is 85 cm. Draw the force diagram for the rod. Clearly label all forces. Write Newton’s 2nd Law equation: (for F of y) Write Newton’s 2nd Law equation: (for net torque) What is the magnitude of the linear acceleration of the block closest to the fulcrum? What is the magnitude of the linear acceleration of the block furthest from the fulcrum?
Robert uses a wrench to turn a stubborn bolt. (a) How much would the torque on the bolt increase if the applied force were double? (b) How much would the torque increase for the original force if a pipe were inserted over the wrench to make the lever arm 3 times as long?
Don't use chat gpt It Chatgpt means downvote
Two forces are applied to a door. Both forces are applied at the door knob, and both forces have the same magnitude. The first force is applied perpendicular to the door, and the second force is applied at 15 degrees to the plane of the door. Which force exerts the greater torque about the door hinge?
An agricultural mechanic tries to loosen a nut on a tractor wheel with a wrench that is 32.5 cm long. If the torque required to loosen the nut is 55.0 N m, what force must she apply to the wrench?
Consider the image below of a wheel that pivots about its center. Force 1 has size 176 N and acts 1.8 m from the center. The angle shown is 36 degrees. Force 2 has size 111 N and acts 0.7 m from the center. The angle shown is 30 degrees. Taking counterclockwise to be positive, calculate the net torque on the wheel, in N m. (Please answer to the fourth decimal place - i.e 14.3225)
A car tire is usually torqued to about 75 foot-pounds. An ft-lb is the English equivalent to theNewton-meter. One ft-lb is equivalent to 1.356 N-m.Assuming the tire iron that comes with the car is 12”in length, what force is necessary if appliedperpendicular to the handle to reach thisrequirement?
For two existing torques, what third force at a given distance from the pivot will balance them? Imagine a meter stick set up as in the figure. It hangs from a central bracket, and two hanging masses can hang from it from each of their brackets. At a third location, a force probe can either pull up or pull down on the stick, depending on what is needed to balance the stick. The mass of the meter stick is 120 g. sketch the situation (drawing r1, r2, r3, F1, F2, and F3) and determine the magnitude (value) and direction (+ or -) of each torque. Don't include the mass of a bracket that would hold the hanging mass in place; assume the mass listed is the entire mass hanging at that point. For each trial, use the principle of equilibrium (where the sum of torques is zero) to calculate the third, unknown force acting at x3