This force-couple system is to be replaced by an equivalent system consisting of the following: a couple moment Mx, and a single force, Rc acting at C. Draw the diagram for the equivalent system and determine Mx and Rc. A 100N 80N 110N-m Thislis not your own propenty so do npt use it in 50N 150N 50N amy way asliffit were your dwn. 130 N D C 180N-m 12° 30N fhis is hot your own propery so do not use t n any way as f it were your own. 1m B. E

This force-couple system is to be replaced by an equivalent system consisting of the following: a couple moment Mx, and a single force, Rc acting at C. Draw the diagram for the equivalent system and determine Mx and Rc. A 100N 80N 110N-m Thislis not your own propenty so do npt use it in 50N 150N 50N amy way asliffit were your dwn. 130 N D C 180N-m 12° 30N fhis is hot your own propery so do not use t n any way as f it were your own. 1m B. E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

600 N 600 N 200 N [02 m 200 N - 3m - 300 N 300 N Determine the resultant couple moment acting on the beam. O 340 Nm CW O 120 Nm CCW O 340 Nm CCW O 280 Nm CW
8. Will upvote to anyone who will answer. Correct units pls. Thanks
The influence line is for V40- = shear just left of 40'. A load of 0.5 kip/ft is placed in such a way to obtain the worst value of V40-. Determine V40- in kips to two decimal places. Use the correct sign. -1 × -7.5 10 0.5 15 20 30 -1
4. the racuitant 15 1275. espectively, acting at an ancient --out of $50 N act simultaneously at a point. Find. Tesmo... CHIC might between them be 15). 5. Find the angle between two equal forces P, when their resultant is equal to (i) P and (ii) P/2. [Ans. 120° N: 151°]
1. Write about the effects of the Stability and Determinaey of Engineering Structures on the economical of the structures in design. 2. For the structural beam shown; noting that the internal hinges lies in the midspan of the beams; find the following: a. Draw the shear and bending moment diagrams. b. Construct Influence Lines for : (Rc, Rr. Sp, Sright-E, Sten-E, Mc, Stet-F) 6.9 W A B
• b1 = 300 mm • b2 = 180 mm . d1 = 250 mm • d2 = 350 mm • f'c = 28 MPa •fy=414 MPa • eccentricity = 500 mm Determine the nominal axial load in kN if it is applied at an eccentricity of 200 mm.
Find the moment at E.
?
*18-32. The linkage consists of two 6-kg rods AB and CD and a 20-kg bar BD. When 0 =0°, rod AB is rotating with an angular velocity w = 2 rad/s. If rod CD is subjected to a couple moment M = 30 N m, determine w at the instant e = 45°. 1.5 m 1m 1m M = 30 N - m
B4
PROB: COMPUTE THE FORCE IN EACH MEMBER OF THE TRUSS Stown In TISE FIGURE USING MOJ. 8kN 24m с 2.4 8kN 41 36m. 2.4m 8 kH 2.4 M. PORTRAIT ORFEntanon. TABULATE YOUR ANSWERS. NO TAB NO PTS.
What is the internal force in member AB? A. 750 N , T B. 450 N , T C. 750 N , C D. 450 N , CSHOW SOLUTIONS