Thevenin source impedance behind the bus equal to 0.002 + j0.01 Q/phase. A power factor-correcting capacitor rated 500 KVAR3, is connected to the bus as shown in Figure P5.5. Determine the parallel resonance frequency and iden- tify the precaution needed for connecting a power electronics load to this bus. Bus 0.002 + j 0.01 2/phase Multiple 'feeders Gen Pf correction capacitors C

Thevenin source impedance behind the bus equal to 0.002 + j0.01 Q/phase. A power factor-correcting capacitor rated 500 KVAR3, is connected to the bus as shown in Figure P5.5. Determine the parallel resonance frequency and iden- tify the precaution needed for connecting a power electronics load to this bus. Bus 0.002 + j 0.01 2/phase Multiple 'feeders Gen Pf correction capacitors C

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Describe the concept of power system harmonics and their mitigation techniques.
Explore the potential of high-voltage direct current (HVDC) transmission systems in interconnecting regional power grids.
The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled real power and reactive powers, and the reactances of transmission lines are marked at this one line diagram (The voltages and reactances are in PU referred to 100 MW base. The active power P2 in MW is the last three digits (from right) of your registration number (i.e for the student that has a registration number 202112396, P2 =396). [10] Starting from an estimated voltage at bus 2, bus 3, and bus 4 equals V2 (0) = 1.15<0°, V3 = 1.15 < 0°, V4 1.1< 0°. 1- Specify the type of each bus and known & unknown quantities at each bus. 2- Find the elements of the second row of the admittance matrix (i.e. [Y21 Y22 Y23 Y24]). 3- Using Gauss-Siedal fınd the voltage at bus 2 after the first iteration. 4- Using Newton-Raphson, calculate: |- The value of real power (P2), at bus 2 after the first iteration. Il- The second element in the first row of the Jacobian matrix after the first iteration. 2 P2…
(c) Figure Q5(c) shows a without and with guard circuit of a Megger insulation resistance instrument. The instrument supplies a test voltage of 15 kV. The measurement without a guard terminal provides a current of 6.1 µA, while the current decrease to 1.1 µA when using a guard terminal. Determine the following: (i) The volume resistance of the cable insulation, ry. (ii) The surface leakage resistance, rs. (d) Discuss the important of guard-wire method in a high resistance measurement.
For the bridge circuits shown in the figure bellow, derive expressions to calculate the unknown impedances. Be Detector wwlle
bus. The voltage magnitude and phase angle are the quantities to be determined after load fiow analysis for
хх X X X ххх ххх ххх ххх 14 - x x x x x X ххх ххх x x x x x xWhat is the initial direction of the deflection of the charged particle as it enters the magnetic field shown in the figure? A) no deflection O B) into the page C) down (bottom of the page) O D) up (top of the page) out of the page
5/The phase angle between magnetizing component current and core loss component current is 180o Select one: True False
Q5: (A) A 100 KVsurge travels on an overhead line of surge impedance 400 Q.The line is connected to a cable of surge impedance 50 Q through a resistance R. Find (1) the value of R that it absorbs maximum energy, and (2) voltage and current transmitted into cable? (B) Explain in details the following phrase (The rate of rise of re-striking voltage will become high if the fault ocurrs near the bus bar of the station?
Choose the right answer. 1. The symmetrical component method is …………. 2. Conditions for succesful operation of a power system ………،……….. and ………… 3. The reason we use the numerical methods in load flow analysis is ……….
bus. The reactive power and voltage angle are determined at the end of load flow analysis for
Q4 (a) (b) A 4-bus power system, as shown in Figure Q4a, of which the parameters are given in Table Q4a; the p.u. value of every component is given based on its own base values (rating). i) Draw an impedance diagram of the network, showing all impedances in p.u., on 1000 MVA and 20 kV base values in the Generator G3 zone. A three-phase short circuit occurs at busbar 3 through a rearance of j0.12 p.u., where the pre-fault voltage is 525 kV and the pre-fault current is neglected. Calculate the short circuit current in p.u. using Thevenin's Theorem. Describe the data required for each component of a typical power network when analysing faults, and the reasons for needing each item of data. T, bus 1 ∞to ΔΥ G₁ G₂ G3 T₁ T₂ Тз Transmission line: 150 Ω bus 4 T₂ bus 2 150 Ω 150 Ω G₂ YE bus 3 T₂ 머( YEA Figure 04a 500 MVA, 13.8 kV, XG1= 0.20 p.u. 750 MVA, 18 kV, XG2 = 0.18 p.u. 1000 MVA, 20 kV, XG3 = 0.17 p.u. 500MVA, 13.8 (A) /500 kV, XT1 = 0.12 p.u. 750 MVA, 18 (A) /500 kV, XT2 = 0.10 p.u. 1000…