There is a counter in the following figure, Which one is correct for the output LEDS after 3th clock signal from t-D0. So Qo Jo J2 +5V O CLK O CLK > CLK O CLK Ko K K Ka 1KN R R R R 100nF 36- II II V IV

Q: Q3/A- For the circuit shown in figure 3 draw the output voltage waveform across the SCR and the…

A: SCR: It is a semiconductor device from the thyristor family used as a switch. It is on when the gate…

Q: Draw the output signals of the circuits in the figure

A: Consider the positive half of the signal;When input voltage starts increasing, up to 10V current in…

Q: In a digital voltmeter, the oscillator frequency is 400 kHz. A ramp voltage to be measured by this…

A: Given, In a digital voltmeter, The oscillator frequency, f = 400 kHz So, time period, T=1f=1400…

Q: Assume each diode to be OFF when V₂ ≤ 0.7V and ON when VĎ >0.7V. Find iD1, İD2, İD³, and vō in each…

A: Given:a circuit,when , the diode is off. when , the diode is on. Find:iD1, iD2, iD3 and v0.

Q: What is Vo across the load? * Implement the ff. in MULTISIM: 100nF Input Voltage AC 1MQ Voltage 75…

A: Given circuit is

Q: d. Period of the source VT R1 1 2 1.0kN VT R2 5 Vrms 60 Hz 3.0kQ R3 3 4.0k2

A: The time period for an alternating wave is the time taken by the wave to compete one cycle. The…

Q: An instrument with IM = 60µA full scale deflection and internal resistance of RM =1kQ is to be…

A: The formula of shunt resistance to be added in parallel is given as: where

Q: Q2. Design a synchronous counter (using JKFF) which has the following state diagram. 010 111 011

A: Available  state 5 hence 3 flipflop is required state table QA QB QC QA+1 QB+1 QC+1 JA KA JB KB…

Q: Draw the drain curve and discuss about the region of operation. When VGS is 4.5V and maximum drain…

A: (a) The curve for drain current s shown below

Q: i need a FSM finite state machine for full adder circuit

A: MOORE TYPE FSM FOR FULL ADDER: In a Moore type finite state machine (FSM), output is solely…

Q: In the figure below, the switch is closed. A diac with breakover voltage VBO = XX-2 V is connected…

A: Given circuit, In the shown diagram value of, XX = 29 YY = 27 ZZ= 15 Given data, Breakover voltage…

Q: C1 =5 µF %3D C3 = 8 µF C2 = 4 µF C4 = 6 µF Cs = 4 µF DURACELL VT = 12 V Vhat is the voltage across…

A:

Q: he three-phase full-bridge rectifier in the below figure has a three-phase source of 480 V rms…

A:

Q: A controlled half-wave rectifier has a 120 V ms 60 Hz ac source. The series RL load has R=30, L 75…

A: Note : As this is the RL load so it can't be solved without the value of β so here I am considering…

Q: What is the output waveform of the circuit? 100 uF PT1 PT2 12V 220 V/60 Hz/0 Deg 1k Ohm 5 V Select…

A:

Q: VTh is the O Short circuit voltage Neither open circuit nor short circuit voltage Open circuit…

A: In this question we will write about Vth...

Q: Explain and discuss how the clamper circuit with biasing voltage work

A: Brief description : In the above given question they have mentioned a clamper circuit and they want…

Q: R1 12 V 56 N 1.0 MN 3 V -12 V

A: Please refer the attached images for the complete answer..

Q: Find out the power of the following signal: x(n)=2ej3n Please show all the steps

A: For any discrete-time signal x(n), the power of the signal can be computed using the following…

Q: Q3/A- For the circuit shown in figure 3 draw the output voltage waveform across the SCR and the…

A: SCR: It is a semiconductor device from the thyristor family used as a switch. It is on when the gate…

Q: What is power dissipation in the Zener diode as shown for (a) RL = 2kΩ (b) RL = 4.7kΩ (c) RL =15 kΩ…

A: According to question:…

Q: Q3/B/ Draw output waveform for following 4-1 multiplexer if the following data input and data select…

A:

Q: Full the following blank (1100 0001 0111 0110)BCD (5321) +(1000 1010 0111)BCD7421=()8

A: It is given that:1100 0001 0111 0110BCD5321+1000 1010 0111BCD7421=8

Q: V1 M R1 12V 00 D1 R2 00 C2 C1 =1μF =9.4nF U1 -vco RST OUT DIS THR TRI сом GND XSC2 Ext Tig 555 TIMER…

A: PART A: Duty cycle 70% and c1 =94FFrequency 5khz:R1 - 1.23 KohmR2 -0.919 Kohm    Frequency 2KHz:R1 -…

Q: Q3/B/ Draw output waveform for following 4-1 multiplexer if the following data input and data select…

A: From the Basics of MUX

Q: Consider a 6 DoF manipulator with variables q1, q2, q3, q4, q5, qnd q6. The position is usually…

A: Generally q1, q2 , q3 gives the position in a 6 DoF manipulator .

Q: Sketch the waveform of vo. Indicate the maximum and minimum value 10 V E

A:

Q: HIGH Jo J2 Q, K1 K2 K3 CLK

A: By observing the above circuit it can be concluded that, For JK flip flop the next state can be…

Q: What is the output waveform of the circuit? 100 uF PT1 PT2 12V + 220 V/60 Hz/0 Deg 1 k Ohm .5V…

A:

Q: Sketch the output voltage in figure (a) for each input voltage (b) and (c) GaAs Vin Vout +11V +4V 0-…

A: KIRCHHOFF’S LAW KCL: The algebraic sum of all currents at a node is zero.           KCL is…

Up-down counter

In digital logic and computing, a counter is a device that stores (and sometimes displays) the number of times a particular event or process has occurred, often in relationship to a clock. A sequential digital logic circuit is the most common type with an input line or clock and multiple output lines. In the binary or binary-coded decimal (BCD) number system, the values on the input line represents a number by several flip-flops connected in a cascaded manner. They are manufactured as separate integrated circuits and are widely used components in digital circuits. These are also a part of larger integrated circuits. These are a specific type of sequential circuit like registers or the value of the flip-flops serving as the output.