The 426-kg uniform beam is subjected to the three external loads shown. Compute the vertical reaction (N) at the support point O if P = 4189 N, Q = 3243 N, T = 40187 Nm, x = 1.02 m, y = 1.43 m, and z = 1.56 m and the system is in equilibrium.Positive values are to the right, up, and counterclockwise. Round off only on the final answer expressed in 3 decimal places.

The 426-kg uniform beam is subjected to the three external loads shown. Compute the vertical reaction (N) at the support point O if P = 4189 N, Q = 3243 N, T = 40187 Nm, x = 1.02 m, y = 1.43 m, and z = 1.56 m and the system is in equilibrium.Positive values are to the right, up, and counterclockwise. Round off only on the final answer expressed in 3 decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A. Determine the magnitude of normal reaction at A B. Determine the x component of the reaction at B C. Determine the y component of the reaction at B
A concentrated load P is supported by two inclined bars as shown. Bar (1) is made of cold-rolled red brass [E = 16,700 ksi; α = 10.4 × 10−6 /°F] and has a cross-sectional area of 0.205 in.2. Bar (2) is made of 6061-T6 aluminum [E = 10,000 ksi; α = 13.1 × 10−6 /°F] and has a cross-sectional area of 0.370 in.2. After load P has been applied and the temperature of the entire assembly has increased by 56°F, the total strain in bar (1) is measured as 1000 με (elongation). Assume θ = 50° and β = 53°.(a) Determine the stress in bar (1).(b) Determine the force in bar (1).(c) Determine the magnitude of load P.
The triangular gate shown in the figure below is hinged at the B and rests on a smooth floor at A, the horizontal component of the reaction at A therefore being zero. The base of gate is 1.295 m and perpendicular to the paper. Determine the vertical component of the reaction at A and the horizontal and vertical components of the reaction at B for the condition: The vertex of the gate is at B, x = 2.95 m, y = 3.95 m and z = 4.95 m.
Q2: For the cantilever beam Shown in Figure 2. Use the data from Table 2. Find the following: I. II. III. The bending moment at B Draw the shear force and bending moment diagrams for the beam The reaction at fixed end Rcy The reaction at the fixed end Mc The shear force at B IV. V. 5kN/m 40 kN A В 2m 2m Figure 2
SITUATION. Consider the figure shown below, neglect the self-weight of members AB and BC. 2.0 m E B +0.9 m-0.9 m- W=5.4 KN → Zoom image Determine the vertical reaction at C. ic 0.8 m 0.4 m
Calculate the reactions on the given beam A В 21 kN/m 2kN/m 6.6m 2.1m Vertical Reaction on A, kN Vertical Reaction on B, kN Answer in numerical values only. If the reaction is upward answer in a positive value, otherwise, answer in negative value
A pipe with a weight of 3.7 kg/m is attached to a wall such that all degrees of freedom are restraint. At the free end of the pipe a vertical load P=100 N pointing downwards is introduced with an excentricity of 100mm from the axis. The pipe has an length of 1m and is made of steel with the Young's modulus of 210 GPa and the Poisson ratio of 0.3125. The moment of inertia is l=19.7 cm“ whereas the polar moment of inertia J = 2 I. First, as part of the mechanical properties determine the Shear Modulus. Then determine the total vertical deflection at the point where the vertical load is being introduced. Note: Use the principal of superposition. ANSWERS: Shear Modulus %3D [MPa] Vertical deflection due to weight only [mm] Vertical deflection due to End-Load (excentricity NOT considered) [mm] Vertical deflection due to excentricity of the End-Load only [mm] Total vertical deflection [mm]
Use E= 200 GPa, I = 800 x 105 mm² when necessary. For the beam loaded as shown, determine the reaction components using Conjugate Beam Method 3.00 3.00 300 kNm 6.00 90 kN/m 7.00 12.0 m 4.00 6.00 P = 229kN
question 1..
For a certain arrangement of two bars carrying only axial forces, the equilibrium and compatibility equations are: Equilibrium: t1+3t2=2kN Compatibility: 2e1 + e2 = 0.1mm There is also a temperature rise of 50oC. Show calculations for the tension in the two bars, where EA=90x103kN and α=12 x10-6 *C for both bars and L1=500mm and L2=400mm.