The wind has deposited sand on a platform so that the intensity of the load is approximately w = 0.5x^3 N / m. simplify the distributed load to a resulting force and specify its magnitude and location from A.

Q: Find the magnitude direction of the force 3 acting compressor if (gamma)os 16 ib/ ft³ ,A is 4ft? v…

A: given; density of fluid (ρ)=16lb/ft3inlet area (A1)=4ft2inlet velocity(V1)=12ft/sdeflection angle…

Q: Q3: Find the magnitude, location and slope of the resultant of the force system shown below.

A:

Q: Find the internal forces at point B.

A: To find Internal forces at Point B

Q: nga rough surlace as suggested in the figure. Which one of the following statements is false? O A…

A: FREE BODY DIAGRAM is a diagram of the system which represents all the forces acting on the system.…

Q: Determine the resultant force for the forces system shown in * fig 37 120N 60 N 20 200MM looN

A:

Q: 200 N 2m1m 100 N 3 m 200N T00 N

A:

Q: etermine the magnitude and the directional angles Əx, Oy, and Əz the resultant force R Fe Fc +

A:

Q: The cable AB supports three vertical loads as shown in next figure. Compute the resultant of these…

A:

Q: -400 mm 300 mm- B, 13 60° 12 52 N 30 N (а) Estimate the Moment about the point A. Your answer is…

A: The horizontal component of force 52 N and 30 N passes through the axis so net horizontal moment is…

Q: A circular flap with a diameter d closes the outflow of water from a tank. The flap rotates around…

A:

Q: Determine the resultant R of the system of distributed loads and locate its line of action with…

A:

Q: •F= 100i-120j+75K act at A •F2=-200i +250j+look act at B Determine Ha resaltant moment Preduces by…

A:

Q: Find the internal forces at point B. 200 N · m A B - 1m 1 m 2 m (а)

A:

Q: Q1) For the concurrent coplanar force system shown below., do the following: 1) Calculate the…

A: To find the resultant of a concurrent coplanar system. At first we need to calculate the summation…

Q: [2] The cable stays AB & AD help support pole AC, which is 2.5 m tall. The tension is 500 N in AB…

A: 22

Q: Replace the loading acting on the beam by a single resultant force. Specify where the force acts,…

A:

Q: A particle is subjected to three vector forces in two dimensions A = (15kN)i + (-22kN)j B=(-12kN)i…

A:

Q: The beam AE is subjected to a system of coplanar forces. Determine the magnitude, direction and…

A:

Q: Replace the distributed loading with an equivalent resultant force, and specify its location on the…

A: Given:

Q: Replace the loading system by a single equivalent resultant force and specify where the resultant's…

A:

Q: A bead of mass 0.1kg is bound to a linear track which connects the points (1,2,3) and (-1,2,4). The…

A: Given: F = (xy2z, x, z2) Points: (1,2,3) to (-1,2,4) To find: Work done

Q: Q9/ If FB = 3 kN and its angle e = 45°, determine the magnitude of the resultant force of the two…

A: Given dataForce in tug A FA = 2kNForce in tug B FB = 3kNAngle of force A with respect to x axis θA =…

Q: B. If the force vector shown below has x, y, and z components of 300 N, 400N, and 800N respectively,…

A:

Q: The sales for the particular product are given for last 7 months. Month Sales Demand February 19…

A: Given data: α=0.2Ft=21At=20 Need to determine the forecasting for September by using the exponential…

Q: 1. Determine the resultant force and specify where it acts on the beam measured from A. 2. 9 kN/m 6…

A: A simply supported beam is given It is required to calculate the resultant force and its distance…

Q: replaces the entire system of forces and gives the same effect as that of the system Resultant…

A:

Q: Determine the force transmitted by the pole and the forces in the two winds

A:

Q: Q2: Determine the internal normal force, shear force, and moment at point B. w N/m Group B: Take w=…

A: Given: w=600 N/m

Q: A traffic signal is shown in the figure below. There are two traffic lights A and B, attached to a…

A: The moment of the forces acting on the traffic lights about point G has been calculated as mentioned…

Q: Compute the work done by the indicated force when the disk undergoes the specified displacement…

A:

Q: Determine the components of the moment (Mx, My, Mz) that the F force will create at the point C in…

A:

Q: 05: Find the magnitude, location and slope of the resultant of the non-concurrent coplanar force…

A: We need to sum the horizontal and vertical forces also take the moment about any point to calculate…

Q: Suppose that w = 220 kN/m. Specify where the resultant force acts on the beam measured from A.

A:

Q: Replace the distributed loading with an equivalent resultant force. Specify the location of FR on…

A:

Q: 400 N/m 200 N/m B 8 m

A:

Q: Combine the two forces P and T, which act on the fixed structure at B, into a single equivalent…

A:

Q: For the loading shown in Figure 5, determine the required intensity (w) and the dimension (d) of the…

A: Find the value of intensity(w) and dimention(d)

Q: Determine the singular equivalent force and distance from end A to it's line of action when Fb is 10…

A: According to the given data We need to find The singular equivalent force and distance from end A

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.