the weight of the trailer is 2130kg, the weight of the tow truck is 6000kg and the slope of the truck is 2% going on a ramp. The speed of 69km/h when first entering the ramp and 320m along the ramp, then 93km/h is the speed. (i) find the total average force on the wheels of the truck. (ii) calculate the average force between the truck and the trailer.

Q: A 119.23-kg skier starts with an initial speed of 29.22 m/s and coasts up a H=6.10-m-high rise as…

A: ma=-mg sinθ-μN    =-mg sinθ-μ mg cosθ    =-mgsinθ+μcosθa=-g(sinθ+μcosθ) acceleration

Q: Let's assume the rocket has a rest length of 57 m and the hangar has a rest length of 51 m.…

A:

Q: In a thunderstorm An comercial airliner need to land on an airport specific runway. Determine the…

A: Plane weight m=50000 kgw=mg=50000×9.81 w=490500 Nv=300 Kmh or v=300×518=83.33 msec

Q: A truck with mass of M is going to tow the car with mass m. For values of M and m please follow the…

A: Mass of the truck→M=150000g Mass of the car→m=800g Initially the truck is moving with 130 Km/h speed…

Q: The escalator steps move with a constant speed of 0.6 m/s. If the steps are 125 mm high and 250 mm…

A: Speed, v =0.6 m/s  Length, l=250 mm  Mass, m = 150 kg Number of steps, n  Height, h = 125 mm The…

Q: A father plays with his little son on a frozen lake. They stood facing each other, put their hands…

A: Given     Acceleration of father, a = 0.8 m/s2               Mass of father, m = 4 M  Where,     M…

Q: The pulley cable is being drawn into drum D with an accelerated rate of 5 m/s?. If the crate has a…

A: Given data: The acceleration of the drum D is. aD=5 m/s2. The mass of the crate is, m=800 kg.…

Q: Don't Use Chat GPT Will Upvote

A: Step-by-Step Calculations:Part A: Minimum Hill Crest Height (h)1. Conservation of Mechanical Energy:…

Q: Given: - The original length (1) of the elastic cord is 2m. - Spring constant is 150 N/m. - 0= 25°…

A: Given that, Length of the cord, l=2 m,Spring constant, k=150 N/m,Angle θ=25°,Mass of the ball, m=6…

Q: In the figure below, a block slides along a track from one level to a higher level after passing…

A:

Q: A100 kg boy starts from rest at the bottom A of a 10-percent incline and increases his sneed at a…

A:

Q: e. A car moving at a speed of 60 km/h is stopped in a distance of 15m. Find (i) average rate of…

A:

Q: -What power output in kW is required to propel a 100kg vehicle up a 30 degree slope at a constant…

A:

Q: The power transmitted by a belt drive is proportional to the Tension as follows P = Tv _wv² Find…

A: Given    P = Power    g = Gravity    v = Velocity Find   Expression for velocity

Q: An amusement park is designing a new ride. The ride is to have a motorized horizontal launch section…

A: Given data: Launch section length = s = 5 m Maximum acceleration = a = 1/3 g  Loaded mass = m = 400…

Q: A 5kg block is pushed up along the slope as shown. The coefficient of kinetic friction is uk =0.2.…

A:

Q: A rope pulls the block up the ramp, as shown in the figure. Find the following:1. What is the…

A:

Q: A vertical take-off and landing aircraft has a mass of 9000 kg. A constant upward thrust of 100 kN…

A:

Q: Calculate your apparent weight at the top and bottom of a Ferris wheel, given that the radius of the…

A:

Q: A happy kangaroo leaps vertically upward at a time t = 0. At time t = 0.50 s the kangaroo is at a…

A:

Q: A helicopter with a mass of 10,000 kg takes off straight up at t=0. The thrust of the engine is…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.