The weight of a specimen immediately after removal from sampler was 35.20 gm and the same specimen after overdrying weighed 20.20 gm. The volume of the sample before drying was found by immersing in mercury to be 25 cc. If the specific gravity of soil solids was 2.70. What were the moisture content, void ratio, degree of saturation, bulk density and drying density of the specimen?

The weight of a specimen immediately after removal from sampler was 35.20 gm and the same specimen after overdrying weighed 20.20 gm. The volume of the sample before drying was found by immersing in mercury to be 25 cc. If the specific gravity of soil solids was 2.70. What were the moisture content, void ratio, degree of saturation, bulk density and drying density of the specimen?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer in two decimal places please
Please write the full solution on a paper, thanks in advance
1. The following are the results of a sieve analysis U.S. Sieve No. 4 10 20 40 60 100 200 Pan Mass of Soil retained (g) 0 18.5 53.2 90.5 81.8 92.2 58.5 26.5 a) Determine the percent finer than each sieve and plot a grain-size distribution curve. b) Determine D10, D30, and Doo. c) Calculate the uniformity coefficient Cu d) Calculate the coefficient of gradation Ce
liquid limit was 25.72%.
It is needed to determine the moist unit weight of the soil for field compaction testing. A silty soil sample has a mass of 612 grams. The soil sample was then covered in beeswax and the combined weight was 650 g. The soil covered in wax, was then immersed in the water and the graduated cylinder registered a volume difference of 404 ml. The wax was gently peeled off the soil. Moisture content = 12% Specific Gravity = 2.78 But if the wax has a specific gravity of 0.94, determine the following: Dry unit weight of the soil Void ratio of the soil % of air in relation to the soil solids of the sample
From Laboratory investigations, the Liquid Limit, plastic limit, natural moisture content and flow index of a soil specimen are obtained as 60%, 27%, 32% and 27, respectively. The corresponding toughness index and Liquidity index of the soil specimen, respectively, are
You are working in a lab and are tasked with determining the percent plant available water for a particular soil sample. You take a field soil sample. The mass of your sample was 152g and it had 18.3% moisture by mass. Then, you place the soil sample in your pressure plate extractor and determine that the soil sample weighs 164.2g when the moisture potential is -33kPa and 130.7g at -1500kPa. What is the percent plant available moisture by mass of this soil sample? Please answer to one decimal place.
I need the answer as soon as possible
The figure and the table below, shows the results of consolidation test for a soil sample, Find the cc value. TI Applied pressure, kPa 25 50 100 200 400 800 Voids ratio 0.634 0.619 0.583 0.523 0456 0383 0.65 0.6 0.55 0.5 0.45 0.4 of 0.35 10 100 1000 PRESSURE 0.15 0.21 0.12 no one 0.30 VOIDS RATIO
A soil sample whose specifications were in the field, the total volume was 1150 cubic centimeters, the total mass was 2290 grams, and the density of the solid was 2540 kg / cubic meter, it was brought to the laboratory and dried in the oven, its mass became 2035 grams, calculate the real characteristics of the model 1- degree of saturation, 2- vacuum ratio, 3- Moisture content, 4- Porosity
As a result of sieve analysis and hydrometer analysis on a soil sample, gravel 40% and sand 18%. Liquid limit value of the soil 58% and plasticity index was determined as 32%. D60, D30 and D10 values according to grain distribution curve 2.4mm, 0.9mm and 0.2mm respectively. According to the findings obtained, the soil sample Make USCS classification.