The wave function for a wave on a taut string is given by y(x,1)=0.35sin 1011-37x+| 3 xx+ where x and y are in meters and r is in seconds, The linear mass density of the string is u=75.0 g/m, (a) Calculate the speed of the traveling wave on the string. (b) Calculate the average rate at which energy is transmitted along the string? (c) Calculate the energy contained in each cycle of the wave?

The wave function for a wave on a taut string is given by y(x,1)=0.35sin 1011-37x+| 3 xx+ where x and y are in meters and r is in seconds, The linear mass density of the string is u=75.0 g/m, (a) Calculate the speed of the traveling wave on the string. (b) Calculate the average rate at which energy is transmitted along the string? (c) Calculate the energy contained in each cycle of the wave?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1 ( shown. * The stresses in a bracket were obtained from a 3D finite element analysis as (a) [A] = 0 (c) [σA] = [20 0 15 (e) [σA] = Which of the following stress tensors [A] correctly corresponds to the stress state at point A, as represented by the infinitesimal cube above. (All units in MPa.) 10 25 L15 25 -30] [-20 0 15 0 -10 -25 15 -25 -30 20 20 0 -15] 0 10 25 -15 25 -30] 30 15 25 25 Y [20 15 0 10 -25 -25 -30. (b) [A] = 15 LO (f) [A] = [20 (d) [A] = 0 L15 0 15 10 -25 -25 -30] OH O 0 [-20 -15] 0 -25 -15 -25 -30] -10
Develop an equation for the transmitted wave height behind a vertical wall extending a depth d into the water of depth h, based on the concept that the wall allows the wave power below depth d to propagate past. Qualitatively, do you believe that your equation for the transmitted wave height will under- or overestimate the actual wave height ? Discuss your results.
Consider the loaded shaft illustrated in Figure Q4 (i). The shaft is simply supported at A and D. The shoulder fillet radius is 0.3 cm at B and C. If the shaft is subjected to a force of F=800 N, determine the following:
The diameter of the ball is 30 cm as shown in figure. Calculate the river current speed m/s. (NOTE: Neglect the weight of the cable. Assume; SGpal=0.20, pwater-1000 kg/m and Cobal=0,2)
A standing wave on a string vibrates as shown in the top diagram. Suppose the string tension is quadrupled and the driving frequency is doubled. Which standing wave pattern is produced? H∞∞þood Original standing wave (a) (b) (c) (d) Copyrigh Person on pubing on on
The wavefunction of a mechanical wave on a string is described by: y(x,t) = 0.012cos(Ttx-100rtt-2Tt/3), where x and y are in meters and t is in seconds. The transverse velocity of an element on the string at the left end (x = O), at time t = O is: %3D O +0.6v3n m/s None of the listed +0.6n m/s O -0.6v3n m/s O -0.6t m/s
i need the answer quickly
P2, µ2 2h P1 Po ρ1, μι L Figure 3: Two layer flow for (b) (b) Consider two immiscible (do not mix) fluid layers with different densities and viscosities which glide smoothly between two parallel horizontal walls, as shown in figure 3. Let pı and p2 be the densities and µ1 and µ2 be the viscosities of the two fluids, respectively. The flow is the result of an imposed constant pressure gradient, 2, similar to that of the Poiseuille flow. Assume a steady, incompressible, parallel viscous flow with p1 > P2 and µi > µ2- (i) Using the Navier-Stokes equations find the velocity profiles of both fluids. (ii) Ensure the fluid obeys the following conditions: The shear stress is continuous at the interface between the two fluids. • The velocity profile is continuous at the interface between the two fluids. No-slip boundary at the walls. (iii) Sketch the velocity profile. (iv) Determine where the maximum velocity occurs and explain why. (Hint: think about the respective viscosities and densities).…
solve the question given in the image.
Question 4 a. Write you understanding about resonance condition for standing waves. Transverse waves travel with a speed of 20.0 m/s on a string under a tension of 6.00 N. What tension is required for a wave speed of 30.0 m/s on the same string?
10 m 1 m 1 m/s Figure 2 Electricity transmission tower Consider 2D, incompressible, steady flow in a vertical channel at a Reynolds number of 100. This channel flow is shown schematically in the figure below. The figure is not drawn to scale. NEGLECT GRAVITY for the sake of simplicity. Channel length 1 and width w are 10 m and 1 m, respectively, as shown in the figure. Assume thickness= 1 m in the z-direction. The velocity is constant at the inlet, in the y-direction and equal to 1 m/s. The Reynolds number is defined as Re . pvw fl where v is the average velocity at any cross-section. Take p = 1 kg/m3 and adjust μ to get the desired Reynolds number. The absolute pressure at the outlet is 1 atm. Note that the cross-section is a square of 1m by 1m. Contrast this to the laminar pipe flow considered earlier where the cross-section was circular. When the cross-section is square or rectangular, this type of a flow is referred to as a channel flow. When the cross-section is circular, the…
Oil flows laminarly through a pipe of 25 millimeters in diameter and 100 millimeters in length. The density of the oil flowing through this pipe changes to 850 kg/m^3 and its flow rate to Q(t)=0,001sin wt.Accordingly, what will be the amplitude (PR) of the pressure drop caused by the fluid resistance and the amplitude (PL) of the pressure drop caused by the inertance?Which W limits should be PR/PL>=0.05In what frequency regions does the pipe behave close to a pure resistance or close to a pure inertance?(if necessary,The absolute viscosity of the oil is u = 30 cp.)