The water vapor is initially at 700 KN / m2 with a 0.05 drought fraction through a reversible process that looks like a half circle when depicted on a temperature-entropy diagram. The final pressure is 100KN / m2 and the final temperature is the same as the initial temperature at 700KN / m2. During the process the maximum temperature is 230 degrees Celsius. For this process specify: A. The process is transferred per kg of water vapor B. Work done per kg of water vapor

The water vapor is initially at 700 KN / m2 with a 0.05 drought fraction through a reversible process that looks like a half circle when depicted on a temperature-entropy diagram. The final pressure is 100KN / m2 and the final temperature is the same as the initial temperature at 700KN / m2. During the process the maximum temperature is 230 degrees Celsius. For this process specify: A. The process is transferred per kg of water vapor B. Work done per kg of water vapor

Similar questions

heat pump operates on a Carnot cycle between the cool exterior of a house and the warminterior. When the exterior temperature is 2.0 °C and the interior temperature is 20.0 °C.a) What is the coefficient of performance for the heat pump?b) The heat pump delivers 63 MJ of energy to the interior of the house. How much energy input isrequired in the form of work?
A heat engine provides a net power output of 14 kW and has an efficiency of 23 %. The engine rejects 1200 J of energy per cycle to a low temperature reservoir. a)Determine the amount of heat delivered to the engine from the high temperature reservoir per second. Your answer should be in units of Watts. b)Determine the required number of cycles per minute executed.
P Example of calculation of work P = 1 Atm V%= 1 litre iii ii P V V,12 V In this cycle the system, which is an ideal monatomic gas, undergoes first isothermal (i) then adiabatic (ii) compression steps, each of which halve the volume, then returns to its starting point via first isothermal (iii) and then adiabatic (iv) expansions, each of which double the volume. How much work is done by the system during the cycle if P, is 1 atmosphere and V, =1 litre?
A certain gasoline engine is modeled as a monatomic ideal gas undergoing an Otto cycle, represented by the p-V diagram shown in the figure. The initial pressure, volume, and temperature are p1 = 1.05 × 105 Pa, V1 = 0.035 m3, and T1 = 290 K, respectively. a)The first step in the Otto cycle is adiabatic compression. Enter an expression for the work performed on the gas during the first step, in terms of V1, V2, and p1. b) Calculate the temperature of the gas, in kelvins, at the end of the first step. c)The fourth and last step in the Otto cycle is isochoric cooling to the initial conditions. Find the amount of heat, in joules, that is discharged by the gas during the fourth step.
A thermodynamic process can be represented using a PV diagram where the pressure and volume at every stage is recorded. In the thermodynamic process shown below the work done by the system is РА A O the area under the PV curve and positive the area under the PV curve and negative B is the product of the change in volume during the process and the change in pressure. cannot be found from the PV graph
Problem #8 In one cycle of an engine, 1.80 kJ of energy is absorbed from a hot reservoir at 280°C, and 1.15 kJ of energy is expelled to a cold reservoir at 25.0°C. a) How much work (in J) is done by the engine in each cycle? b) What is the engine's efficiency? c) How does this compare to the Carnot Efficiency?
A refrigerator has a coefficient of performance of K=2.2 Each cycle, it absorbs 3.35×104 J of heat from the cold reservoir. The refrigerator is driven by a Carnot engine that has an efficiency of e=0.5. A)How much mechanical energy is required each cycle to operate the refrigerator? B)During each cycle, how much heat flows into the Carnot engine?