The water level in a lake is 5m above the bed, and the saturated unit weight of lake bed soil is 20kN/m³. The unit weight of water is 10 kN/m³. What is the effective vertical stress at 5m depth below the Jako hod?

Q: View Policies Current Attempt in Progress Water flows over the spillway shown in the figure below.…

A:

Q: AW360 x 72 standard steel shape is used to support the loads shown on the beam in Figure A. The…

A: Given data,Fig is givenP=5.7KNw=15.6KN/mM=44KN.ma=1.45mFINDMaximum tensile bending stressMaximum…

Q: Situation 1 Given spot levels determine the total amount of trucks with capacity of 20 cubic meters…

A:

Q: An interior column is to be designed as a part of an unbraced frame system, located at the ground…

A: Le = kL = 1*3 = 3m = 3000 mmPu = 1.2*300 + 1.6*350 = 920 KNFor A36fy = 250N/mm2

Q: 11.89 A ball is thrown so that the motion is defined by the equations x = 5t and y = 2 + 6t - 4.912,…

A:

Q: Water flows under the sluice gate shown in the figure below. Determine the flowrate if the gate is…

A:

Q: Small-diameter, high-pressure liquid jets can be used to cut various materials as shown in the…

A: Reference : Fluid mechanics,Water jet pressure. Given : 0.1 mm diameter and 690 m/s To find : 1.…

Q: b) Determine the transformation matrix of all elements.

A:

Q: A 40-lb aluminum bar, initially at T₁ = 150°F, is placed in a tank together with 190 lb of liquid…

A: Given data: Weight of aluminium bar=40 lb Temperature of aluminium, Ta=150°F Tank of water with…

Q: 3. Calculate the SDI for the following samples. Determine if the water needs to be pretreatment…

A: To calculate the SDI, we use the following formula:SDI = (1 - Ti / Tf) * 100 / Ttwhere:Ti is the…

Q: I) Determine the force in member DE of the truss. K J H G A A B 4 ft I O C o D E -3 ft 3 ft 3 ft 3…

A: Method of section is used to calculate Force in member DE  Taking moment about  G  To get Force in…

Q: PC1 PI1 0+000 Lct PT1 R1 11 STATION NORTHINGS EASTINGS 0+000 11475.55 8927.24 PC2 9291.91 9546.66…

A: To Determine Table 3 ( The Stationing of PC, PT, PC2, PCC, PT2, PC3, PRC, PT3 and End of Project)…

Q: Part

A:

Q: 11 fá = 4 ksi Grade 60 sted NWC. M=110ft-* for the all questions. Computer the bending stresses in…

A:

Q: 3. Determine the magnitudes of the forces in each pin of the loaded frame. P R 42° C 42° P B

A: To Determine :-  Magnitudes of the forces in each pin of the loaded frame.

Q: A rigid, insulated vessel is divided into two compartments connected by a valve. Initially, one…

A:

Q: At the location of the maximum positive moment, determine the maximum tension bending stress, 7+.…

A: A cantilever beam is given with an upward UDL and a point load is applied on it as given.The…

Q: D,E,F,G,H

A: A structure is static determinate when it's   Ds=0. We have 3 equilibrium equation out there... 1)…

Q: '. (a) Compute the runoff from a 7-in rainfall on a 1500-acre watershed that has hydrologic soil…

A:

Q: Water flows in a steel pipe (ɛ = 0.00020 feet) at a flow Q = 12.5 cfs. The diameter of the pipe is D…

A: Given that:                           Surface roughness, ∈=0.00020 ftDischarge, Q=12.5 cfsDiameter…

Q: Problem 2. A well is located in a completely confined aquifer with a hydraulic conductivity of 12…

A:

Q: Part

A:

Q: Water contained in a closed, rigid tank, initially at 100 lbf/in², 800°F, is cooled to a final state…

A:

Q: 5. Segment AB of the bar is a tube with an outer diameter of di and a wall thíckness of 0.125 in.…

A: To Find:- Diameter d1 Diameter d2

Q: Part 8

A: Data given Load P = 250 kN Modulus of Elasticity of Steel, Es = 200 ×106 kN/m2 Modulus of…

Q: For the body below, determine the centroid under the reference frame shown. Y 2

A:

Q: part 4 and 5 please

A: Determinea. Maximum positive and negative bending moment. b. Moment of inertia about centroid…

Q: 7.20 Estimate the hydraulic conductivity of a saturated clay having a clay-size fraction, CF = 42%,…

A:

Q: Part

A:

Q: 6. A biodegradable fuel having a specific gravity of 0.95 and a viscosity of 0.04 grams per cen-…

A: Solution (6) Reynolds number of the biodegradable fuel is calculated by. Re =ρvDμv =Re ×μρD Where, ρ…

Q: If F = 730 lb, F = 380 lb, F 620 lb, determine the magnitude of the resultant force acting on the…

A: Resultant force is the sum of all the forces acting horizontally and vertically.We can calculate…

Q: A rectangular plate is submerged in water as shown below. The top of the blue region is the surface…

A:

Q: The cantilever beam shown in Figure A is subjected to load magnitudes o shown in Figure B has…

A:

Q: 643-218

A: Note: As you have nothing mentioned in this problem. So, we are assuming that we have to apply…

Q: 2. Verify that the function y = Ciex + C2e2x is a solution of the differential equation y" – 3y' +…

A:

Q: View Policies Current Attempt in Progress (Bernoulli/continuity) Water flows steadily through a…

A:

Q: al, determine the initial velocity vo of the snow.

A:

Q: °Prob. 2.9-4. Determine the allowable tensile load P for the prismatic bar shown in Fig. P2.9-4 if…

A:

Q: f. Assuming a porosity of 18% for the sandstone, what is the seepage velocity for that unit? g. How…

A:

Q: (Bernoulli/continuity) Water flows into a large tank at a rate of 0.011 m³/s as shown in the figure…

A:

Q: A monorail train starts from rest on a curve of radius 400 m and accelerates at the constant rate…

A: Given: Radius of curve, ρ = 400m, v = 72km/h= 20 m/s

Q: #3 Classify each of the following trusses as statically determinate, statically indeterminate, or…

A:

Q: Part 3 Determine the bending moment acting at each of the following locations: (a) x = 1.45 m (ie,…

A: Given data,fig is given P=5.7KNw=15.6KN/mM=44KN.ma=1.45mFINDPart 3)determine the bending momentat…

Q: P2.10. Refer to Figure P2.9 for the floor plan. Calculate the tributary areas for (a) floor beam B3,…

A: Note : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Gasoline flows steadily downward through the pipe shown in the figure below. Viscous effects are…

A: Given data: P1=0

Q: Air enters a compressor operating at steady state at 15 lbf/in.², 80°F and exits at 200°F. Stray…

A:

Q: 2. A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial…

A: Note :- as per our guidelines we are supposed to answer first three subparts only. Please repost…

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.