- The wall of a steel tank containing aerated water is corroding at rate 55 mdd1-How long the time will it take for the wall thickness to decreases by 0.8 mm.2- What rate corrosion in mpy? p of Fe= 7.87 g/cm³

Given that- Corroding rate, Cr= 55 mdd = 55 mg/dm2 day Converting the value into g/cm3day- Cr=55…

Answered: The wall of a steel tank containing…

Introduction to Chemical Engineering Thermodynamics

8th Edition

ISBN:9781259696527

Author:J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart

Publisher:J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart

Chapter1: Introduction

Section: Chapter Questions

Problem 1.1P

See similar textbooks

Similar questions

A thick cylindrical pipe with length of 1 m and an inner diameter of 20 mm and an outer diameter of 120 mm is insulated with two layers of insulating materials. The thermal conductivity and thickness of each insulating material are as follows: Pipe k = 500 W/m-K, Insulator A = 0.10 W/m-K ; thickness = 30 mm Insulator B = 0.05 W/m-K; thickness = 30 mm Air at 200 C is flowing through the pipe. The temperature of the outer surface of the pipe is 43 C. Steady state heat transfer is occurring across radial direction. The heat transfer coefficient are as follows : h inside = 25 W/m²K and h outside = 45 W/m²K Calculate the total heat loss, the overall heat transfer coefficient, the temperature between the insulator A and B, and the temperature between the outer diameter and insulator A.
A 10 cm thick piece of beef steak will be frozen in the freezer room -40 ° C. This product has a moisture content of 73%, a density of 970 kg / m³, and a thermal conductivity (frozen) of 1.1 W / (m K). Estimate the freezing time. using the Plank equation. This product has an initial freezing temperature of -1.75 ° C, and the movement of air in the freezing room gives a convective heat transfer coefficient of 15 W / (m² K). t f = hour
A large concrete slab 1 m thick has one dimensional temperature distribution given by T = 4-10x+20x²+10x³, where T is temperature and x is distance from one face towards the other face of wall. If the slab material has thermal diffusivity of 2 x 10^(-3) m²/hr. The rate of change of temperature of the outer face of the wall is given as?
Heat transfer
kindly answer this heat transfer problem. thank you
The viscosity of honey is about 1 Pa-s. The viscosity of water at 20C is about 1cp. How many times is honey more viscous than water? A) 10 B 1000 100 D) 10000
Research has shown that tomato ketchup has the following viscous properties at 25°C. Consistency coefficient K = 18.7 Pa s" Power n = %3D 0.27 Shear yield stress = 32 Pa Calculate the apparent viscosity when the rate of shear is 1, 10, 100 and 1000 s and conclude on the effect of the shear rate on the apparent viscosity.
Q3) A fused-quartz sphere has a thermal diffusivity of 9.5 x 107 m²/s, a diameter of 2.5 cm, and a thermal conductivity of 1.52 W/m. °C. The sphere is initially at a uniform temperature of 25 °C and is suddenly subjected to a convection environment at 250 °C. The convection heat-transfer coefficient is 110 W/m². °C. Calculate the temperatures at the center and at a radius of 5 mm after a time of 8 min.
1. A layered wall consists of a copper plate with a thickness of 2.5 cm, the second layer is made of asbestos, the thickness is 3.2 mm, and the third layer is made of glass fiber with a thickness of 5 cm. The overall temperature difference of this wall is 560 ° C. a. Calculate the overall heat transfer rate on this layered wall. b. Calculate T2 and T3
What is the enthalpy change that occurs when 1 gallon of water is heated from 60 oF to 1100 oF at a pressure of 240 psia
A composite wall consisting of five series layers of materials with different properties. Layer thickness, thermal conductivity of the layers and temperatures are shown on the figure. Based on Fourier's law for conduction, answer the following questions. 1. What are the main assumptions? 2. Drive an equation to calculate the heat transfer rate through the Composite wall? 3. Draw the thermal circuit through composite wall? 4. What are the value Ti? 5. What are the value Tj? 6. What are the value Tr? Givens: KA = 2 W/m. °C KB = 1 W/m.°C Kc= 5 W/m. °C Kp= 4 W/m. °C 100°C Ti 25°C Tj Tr А C D +2cm + 6 cm- -4 cm 4cm
Problem 3: For a sandstone reservoir, calculate the water saturation if the porosity (Ø) is (20 %), the resistivity of the formation water (Rw) is (0.09) and the true resistivity (Rt) is (15)? Ruohlam 1

SEE MORE QUESTIONS

Recommended textbooks for you

Introduction to Chemical Engineering Thermodynami…

Chemical Engineering

ISBN:

9781259696527

Author:

J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart

Publisher:

McGraw-Hill Education

Elementary Principles of Chemical Processes, Bind…

Chemical Engineering

ISBN:

9781118431221

Author:

Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard

Publisher:

WILEY

Elements of Chemical Reaction Engineering (5th Ed…

Chemical Engineering

ISBN:

9780133887518

Author:

H. Scott Fogler

Publisher:

Prentice Hall

Introduction to Chemical Engineering Thermodynami…

Chemical Engineering

ISBN:

9781259696527

Author:

J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart

Publisher:

McGraw-Hill Education

Elementary Principles of Chemical Processes, Bind…

Chemical Engineering

ISBN:

9781118431221

Author:

Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard

Publisher:

WILEY

Elements of Chemical Reaction Engineering (5th Ed…

Chemical Engineering

ISBN:

9780133887518

Author:

H. Scott Fogler

Publisher:

Prentice Hall

Process Dynamics and Control, 4e

Chemical Engineering

ISBN:

9781119285915

Author:

Seborg

Publisher:

WILEY

Industrial Plastics: Theory and Applications

Chemical Engineering

ISBN:

9781285061238

Author:

Lokensgard, Erik

Publisher:

Delmar Cengage Learning

Unit Operations of Chemical Engineering

Chemical Engineering

ISBN:

9780072848236

Author:

Warren McCabe, Julian C. Smith, Peter Harriott

Publisher:

McGraw-Hill Companies, The

SEE MORE TEXTBOOKS

The wall of a steel tank containing aerated water is corroding at rate 55 mdd 1-How long the time will it take for the wall thickness to decreases by 0.8 mm. p of Fe= 7.87 g/cm³ 2- What rate corrosion in mpy?