The wall is 2.5 m high and consists of 51 mm x 102 mm studs plastered on one side. Onthe other side is 13 mm fiberboard, and 102 mm clay brick. Determine theaverage load in kN/m of length of wall that the wall exerts on the floor.25 m

For studs Weight =0.57kN/{ m }^{ 2 }\left( 2.5m \right) =1.425kN/m=0.57kN/m2(2.5m)=1.425kN/m For…

Answered: The wall is 2.5 m high and consists of…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A slab panel is carrying a superimposed dead load of 2.70 kPa and superimposed live load of 6.0 kPa all over the 4.0 m x 18 m light storage area. The slab is restrained. The concrete to be used has strength of 28 MPa (normal weight). The main reinforcement has yield strength of 350 MPa. Use concrete cover of 20 mm. The thickness uses a multiple of 10 mm. The main reinforcement used is 16 mm in diameter The shrinkage and temperature reinforcement used is 12 mm in diameter The unit weight of concrete is 23.6 kN per cubic meter. Using USD, Determine the spacing of 12 mm main rebar at the support.
2. A masonry terrace of 85mm thick concrete surface with 35mm thick cement tiles rest on 200mm x 250mm timber spaced at 350mm on centers acting as simple beam with effective span of 3.8 meters. Weight of wood is 9.5Kn/M^3 and masonry to be 20KN/m^3. Ew = 13.8GPA. %3D CEMENT TILES Given: 65 %3D Allowable stresses for bending = 14 MPa Seil 250 For shear parallel to the grain = 0.9 MPa FLOOR 200 01ST Deflection = 1/360 of span %3D 250 350 200 a. Determine the uniform load it could support with respect to bending. b. Determine the uniform load it could support with respect to shear. c. Determine the uniform load it could support with respect to deflection.
Make a good quality solution
A floor panel 3 4 m wide and 12 m long is intended for a vibratory machine in a factory. The concrete to be used has a strength of 27.6 MPa (whose density is 1800 kg per cubic meter) and reinforcement used has yield strength of 280 MPa Determine the minimum thickness of slab if the panel is cantilever
2. A reinforced concrete beam having a width of 280 mm and a total depth of 600 mm is reinforced for tension at the bottom with 6 - 36 mmɸ bars placed on two layers, 4 bars on first layer and 2 bars on second layer. Compute the effective depth of the beam and the clear horizontal spacing between bars.
A concrete wall is 4m high, 6m long, and 4 in thick. Determine the number of 4kg. cement, sand and gravel required using concrete class AA.
The floor shown below with an overall depth of 125 mm is to be designed to carry an imposed load (LL) of 2.5 kN/m² plus floor finishes and ceiling loads (DL) of 1.5 kN/m². Calculate the factored loads acting on beams CD. Assume unit weight of concrete is 24 kN/m². E 2. F 3.0 m 5.0 m Depth 125mn 0.125m -hh=2.5 kN/m² - PL = 1.5 kNm² - u. W of compete 24 KN/m³ A 80m B
ALLE A square lead slab of side 50 cm and thickness 10 cm is subjected to a shearing force (on its narrow fa of 9 x 104 N. The lower edge is riveted to the floor. How much will the upper edge be displaced? (Shear modulus of lead 5.6 x 109 N m²) (4) 1.6 cm (1) 0.16 mm (2) 1.6 mm (3) 0.16 cm
The sign post shown has an outside diameter of 12-in. and a wall thickness of 0.50-in. Determine the maximum load P that can be applied while limiting the maximum tensile stress at the base to < 36 ksi. 1.5P P 10 ft 7 ft C 20 ft D.
How do you prefer a ‘tracked drive’ system than a ‘tired drive’ system for an excavator?
10.37 FLUS Water (20°C) flows in a 16-cm cast-iron pipe at a rate of 0.1 m/s. For these conditions, determine or estimate the following: a. Reynolds number b. Friction factor f (use Swamee-Jain Eq. (10.39) in §10.6.) c. Shear stress at the wall, To
Calculate the weight of the wall from the given Cross Section by considering the unit weight ofreinforced and plain concrete as γc=23 kN/m3.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

The wall is 2.5 m high and consists of 51 mm x 102 mm studs plastered on one side. On the other side is 13 mm fiberboard, and 102 mm clay brick. Determine the average load in kN/m of length of wall that the wall exerts on the floor.