The volume flow rate of water is 661,68 liters/min. Calculate the maximum length of the pipe [m], which can be used without cavitation? (NOTE: Take water temperature as 10 °C) Length e D-0.07 m (-0.08 mm Elevation 650 m Elevation 653 m

The volume flow rate of water is 661,68 liters/min. Calculate the maximum length of the pipe [m], which can be used without cavitation? (NOTE: Take water temperature as 10 °C) Length e D-0.07 m (-0.08 mm Elevation 650 m Elevation 653 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Determine whether the following equations are dimensionally homogeneous. pl t = mf represents an…

A: Given: The expression is t=plmf. l is acceleration, p is pressure, m is weight, t is time, f is…

Q: The cylindrical tank with hemispherical ends contains a volatile liquid and its vapor The liquid…

A: Patm =100 Kpa (S.G.)mercury =13.6 Absolute pressure in the vapor =120kPa Atmospheric pressure =…

Q: a · x + b What is the dimension of the bi-linear form, when [a] = M²L'T-1, [b] = MªL'T-1, and C• x +…

A: Data given- [a] = M2 L1 T-1 [b] = M4 L1 T-1 [c] = M-1 L-2 T1

Q: Determine whether the following equations are dimensionally homogeneous. 2ph3 f = mh 3t2 f is a…

Q: N/m². The flow is steady, incompressible, and fully develc

Q: Ę TO n A x-axy F₁ M&F Yo Criven Q₁ = 15° 8₂=15° F₁ = F₁ = ± < 20, 5₁, -27 [N] r = 0.260 Find the…

Q: Water enters the piping arrangement shown in the figure at a volumetric flow rate Q1=0.4 m^3/s. The…

Q: In the gap between the two plates, the lubricant flows in one direction (x) by the pressure…

A: Write the given data. ∆PL=25000 Pa/mB=6 mm=0.006 mμ=25×10-3 Pa·sρ=0.88 g/cm3=880 kg/m3

Q: 3. Determine: (a) The equivalent length in meters of pipe that would have the same loss as a fully…

A: As per the rules, only the first three sub-parts will be answered. For the commercial steel pipe,…

Q: The nozzle impinges a jet of air at 332 ft/s at a volume flow rate of 92.8 cfm onto the right angle…

A: The speed of the jet of air is V = 332 ft/secThe discharge is Q = 92.8 cfm = 1.55 ft3/secThe…

Q: Engine oil at 40 C [density 876 kg/m^3, viscosity 0.2177 kg/m.s] flows in a 20-cm-diameter pipe at a…

A: The density of engine oil is ρ=876 kg/m3. The dynamic viscosity of engine oil is µ=0.2177 kg/m.s.…

Q: In the gap between the two plates, the lubricant flows in one direction (x) by the pressure…

Q: The controversial Cape Wind project proposes 130 large wind turbines in Nantucket Sound, intended to…

A: Solution: Given: 75% electric power need Diam. of turbine=100, wind velocity=7m/s To…

Q: The venturi meter has water flowing through it. The pressure difference is 6894.6 Pa. The diameter…

Q: Air at a temperature of 25°C and standard atmospheric pressure of 101.3 kPa flows through the nozzle…

A: K=1.4To find:

Q: Determine: (i) pressure at C [-31.86 kN/m²] (ii) input power to motor [2.2.kW]

Q: Air at a temperature of 25∘C∘C and standard atmospheric pressure of 101.3 kPakPa flows through the…

Q: TA The nozzle impinges a jet of air at 332 ft/s at a volume flow rate of 92.8 cfm onto the right…

A: Velocity of jet, V = 332 ft/sVolume flow rate, Q= 92.8 cfm=1.5467 ft3/sAssuming the specific weight…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

The volume flow rate of water is 661,68 liters/min. Calculate the maximum length of the pipe [m], which can be
used without cavitation? (NOTE: Take water temperature as 10 °C)
Length e
D-0.07 m
-0.08 mm
Elevation
650 m
Elevation
653 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

SOLVE CAREFULLY!! Please Write Clearly and Box the final Answer(s) Use THE CORRECT UNITS and show your work!
Engine oil at 40 C [density 876 kg/m^3, viscosity 0.2177 kg/m.s] flows in a 22-cm-diameter pipe at a velocity of 1.1 m/s. The pressure drop (in Pa) of oil for a pipe length of 24 m is ?
PLEASE answer question NUMBER 5 only, please be clear and thanks in advance for answering only number 5. Suppose you will need to repair the pipe between connections A and B, you will want to havethe flow between A and B as minimal as possible. What is the minimal value of x6 to have afeasible solution. PLEASE answer question NUMBER 5 only, please be clear and thanks in advance for answering only number 5.
At room temperature, the water in the storage tank is pumped up to the top of the absorption tower at a flow rate of 10.8 m3/h. The point at which the upward water is discharged is in the atmosphere at a height of 5 m from the surface of the water storage tank. Calculate the friction loss during transportation [J/kg] when the inner diameter of the transport pipe is 50mm, the efficiency of the pump is 50% and the pump work (Wp) is 150J/kg (=m2/s2). However, it is assumed that the area of the liquid level of the water storage tank is very large compared to the cross-sectional area of the transport pipe outlet.
Engine oil at 40 C [density 876 kg/m^3, viscosity 0.2177 kg/m.s] flows in a 20-cm-diameter pipe at a velocity of 0.9 m/s. The pressure drop (in Pa) of oil for a pipe length of 20 m is
The oil is pumped from a reservoir tank to the automobile tank. The volume flow rate of oil is 3,2 cm/s. The pipe diameter is 5 mm. The oil discharges through a 0.8-mm nozzle in a tank. The pressure in the tank is 95 kPa. The total head loss in the system is 1.1 m. If the pump has an efficiency of 58,18%, determine the power [W] needed by the pump. (NOTE: Po = 673 kg/m) 05 m 95 kPa 100 kPa Pump
Add the energy grade line (EGL) as a solid line and the hydraulic grade line (HGL) as a dashed line to the figure below. Enter the corresponding numbers in the table. Assume steady incompressible flow from left to right. At point A, the pressure head P/y = 8 ft and the velocity is V=8 ft/s. The first turbine extracts AH = 10 ft, and the second turbine extracts AH = 5 ft. [ft] Ply Z V²/(28) EGL HGL EGL and HGL [ft] 30 25 2 10 50 O >> EGL_HGL (2,2,2,'T','T',-30,'ft') A D₁ =2 ft B C D₂ =2 ft; DE P3 = 2 ft F 0 5 A 10 B 20 25 15 x [1000 ft] C D 30 E F
Engine oil at 40 C [density 876 kg/m^3, viscosity 0.2177 kg/m.s] flows in a 21-cm-diameter pipe at a velocity of 1.1 m/s. The pressure drop (in Pa) of oil for a pipe length of 24 m is ?"
Prob1 h₁ = 5√²₁/2g (at section A) hf 0.05 ²₂/2g (at nozzle) Find; Q=.....[m³/s]; PA=......[kN/m²]; Use: H = 8 m; v₁ = 1.32 m/s; v₂= 12 m/s Water 150 mm -V₁ A √₂ d₂= 50 mm