The volume and pressure of a gas are 7.40 m³ and 2,10 atm, respectively. (a) If this gas expands to one and one-half its initial volume while the pressure is constant, determine the work done on the gas. J (b) On the other hand, if this gas is compressed to two-fifths its initial volume while the pressure is constant, determine the work done on the gas.

The volume and pressure of a gas are 7.40 m³ and 2,10 atm, respectively. (a) If this gas expands to one and one-half its initial volume while the pressure is constant, determine the work done on the gas. J (b) On the other hand, if this gas is compressed to two-fifths its initial volume while the pressure is constant, determine the work done on the gas.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A vertically arranged piston-cylinder assembly with a mass and area of a piston given as 57 kg and 0.0106 m?, respectively is filled with 4 g of carbon dioxide (CO,). The initial volume and specific internal energy of the gas are 0.0047 m and 604 kJ/kg, respectively. The piston is exposed to the atmosphere and pressure of 100 kPa is exerted on the top of the piston by the atmosphere. The volume of the gas has decreased to 0.0024m when 2 kJ heat is transferred slowly from the gas to the surrounding (a) the pressure, in kPa, and (b) the final specific internal energy, in kJ/kg Assume: The local gravitational acceleration to be 9.81 m/s? Friction between the piston and the cylinder is neglected.
A 2 kg of steam occupying 0.3 m at 15 bar is expanded according to the law pvl3 = constant to a pressure of %3D 1.5 bar. The work done during the expansion will be
Four kilograms of carbon monoxide (CO) is contained in a rigid tank with a volume of 1 m3. The tank is fitted with a paddle wheel that transfers energy to the CO at a constant rate of 14 W for 3 h. During the process, the specific internal energy of the carbon monoxide increases by 10 kJ/kg.If no overall changes in kinetic and potential energy occur, determine:(a) the specific volume of the carbon monoxide at the final state, in m3/kg.(b) the energy transfer by work from the carbon monoxide, in kJ.(c) the energy transfer by heat transfer to the carbon monoxide, in kJ.
Nitrogen undergoes an adiabatic process, the pressure volume relationship given as p = (5/V)+1.5 where is in bar and V is in m3. During the process the volume changes from 1.5 x 108 mm3 to 0.05 m3 and the system takes 45 kJ of heat. Determine (i) Work done (i) Work done (ii) Change in internal energy (iii) Final pressure of the gas, if the initial pressure is 1 bar (iv) Final temperature of gas, if the initial temperature is 80°C (v) mass (vi) Change in enthalpy .
THERMOFLUID A frictionless piston-cylinder contains 3.30 kg of saturated water at 1 MPa. The water is expanded at constant pressure until its temperature rises to 270 °C. The image of the system and process are shown in Figure 3. Determine: iii) final state of water in cylinder after expansion process, and show your evidence.
As shown in the figure below, a cylinder fitted with a piston is filled with 600 lb of saturated liquid ammonia at 45°F. The piston weighs 1 ton and has a diameter of 2.5 ft. * Your answer is incorrect. V= What is the volume occupied by the ammonia, in ft3? Ignoring friction, determine the force required, in lbf, by mechanical attachments, such as stops, to hold the piston in place. What is the volume occupied by the ammonia, in ft³? i 15376500 Patm = 1 atm Piston ft3 Ammonia Saturated liquid - Weight = 1 ton D=2.5 ft
One kg of steam at 124 degree Celsius and 10% moisture undergoes a constant volume process until the pressure becomes 0.28 MPa. Determine the following(a) final temperature(b) Q in KJ(c) at what pressure was the final condition saturated?
1
3
A piston-cylinder device contains an ideal gas of nitrogen. At the initial state, the volume is V1= 1.00 m3, the pressure is p1= 400.00 kPa, the temperature is T1= 300.00 K. An electric heater within the device is turned on for a time of Δt = 5.00 min. The current is I = 3.00 A, and the source voltage is V = 120.00 V. During the heating process, the gas expands, and a heat loss of Qout = 2.80 kJ occurs. The gas constant is R = 0.297 kPa·m3/(kg·K), and the room temperature specific heat at constant pressure is cp =1.039 kJ/(kg·K). Calculate the electrical work done on the gas, Wele__________ (kJ)