Answered: The ventilator door in Fig. P6-11 is…

The ventilator door in Fig. P6-11 is neld in the horizontal position by cable AB. Find the rectangular com- ponents of tension T in cable AB acting at A.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.18P: For the ladder in Prob. 6.17, find the internal force system acting on section 2, assuming that x <...

See similar textbooks

Similar questions

Solve the preceding problem for the following data: b = 6 in., b = 10 in, L = 110 ft, tan a = 1/3, and q = 325 lb/ft.
4. The access door in Fig. P6-13 is held in the position by cable AB. If the magnitude of tension T in the cable is 50 pound force, find the rectangular components of T acting at A. 10 in. B 10 in. 12 in. 6 in. 20° FIGURE P6-13
(1) IN Z 60 in B cord ले Q=ib 70 in 10 insi C In cord 42 (W = TBD A 1 16 45 in P = 42 16 Q = 54 16 x A block of weight W is suspended by two cords, AC and BC, shown, and forces P (in the x direc) and Q (in the z direc) are exerted at C. Find the weight W of the block, and the fensions TAC and Ter in the two cords. Ас BC
A load weighing P kN aswith AB, AC and AD cables such asare carried. Points A and B are x-axis, Cand D points are on the y-z plane.Specific to your name in the data tableAB, AC and AD cable using ratingsCalculate the forces. P (kn) = 440 L1 (m) = 11 L2 (m) = 10 L3 (m) = 16 L4 (m) = 18 L5 (m) = 16 L6 (m) = 5
A ladder carried by a fire truck is 20.0 m long. The ladder weighs 3400 N and its center of gravity is at its center. The ladder is pivoted at one end (A) about a pin (Fig. ); ignore the friction torque at the pin. The ladder is raised into position by a force applied by a hydraulic piston at C. Point C is 8.0 m from A, and the force F S exerted by the piston makes an angle of 40° with the ladder. What magnitude must F S have to just lift the ladder off the support bracket at B? Start with a free-body diagram of the ladder.
W1 weight is dropped from height h towards W2 weight,W1=40N,W2=400N,h=200mm, k=32 kN/m.Find the maximum values of the spring force and the bending amount of W2.Consider the impact of between W1 and W2 is not flexible,it's rigid, ignore the weight of spring,and solve it using energy conversation method. I am Turkish,if my english is bad I am so sorry I did my best.Can you help me about this problem?
A lifeboat hangs from two ship’s davits, asshown in the figure. A pin of diameter d = 0.80 in.passes through each davit and supports two pulleys,one on each side of the davit.Cables attached to the lifeboat pass over the pulleysand wind around winches that raise and lowerthe lifeboat. The lower parts of the cables are verticaland the upper parts make an angle α =15° with thehorizontal. The allowable tensile force in each cableis 1800 lb, and the allowable shear stress in the pinsis 4000 psi. If the lifeboat weighs 1500 lb, what is the maximumweight that can be carried in the lifeboat?
Two gondolas on a ski lift are locked in the position shown in the figure while repairs are being mnade elsewhere. The distance between support towers is L- 30.5 m. The length of each cable segment under gondola weights Wg = 2000 N and Wc- 2900N are DAB = 3.7 m. DBC = 21.4 m, and DCD = 6.1 m. The cable sag at B is 3.9 ft and that at C is 2.3 m. The effective cross-sectional area of the cable is A =77 mm. Which of the following nearly gives the tensile stress on cable %3D AB? 43 B 4c WB Support tower L= 30.5 m- 13.67 ksi O 12.8 ksi
3 Show complete solution and draw each step by step. the answer are 218 kN, 180 kN, 191 kN
The structure ABCD (shown below) is designed to support a finite mass hanging from a cable, DF, attached to the structure at point D. x=8m, y=6 m, and z-15 m. The structure is mounted to the ground by a hinge at B and a roller at C and is also supported by a horizontal cable, AE, attached to the wall. The mass of the object hanging from cable DF is 500 kg. The tension in the support cable AE is 1.000 × 10³ N. Determine the force in each member and the reaction forces. E D
12 pies -5 pics- B find all the forces and reactions P=8000pounds -5 pies P Statics -6 pies-
The uniform bar AB weighing 240 lb. is mounted as shown in Figure upon a carriage weighing 480 lb. The center of gravity of the carriage is at C midway between the wheels. If P = 180 lb. and there is no frictional resistance at the wheels, find R1 and R2, and also the horizontal and vertical components of the pin pressure at A.