The variable A is stored at memory address 24. We want to change its value to 512. Which of the following combinations of R5, R6, and the constant X will accomplish this with the instruction sw R6, X(R5)? Briefly explain. Note: more than one answer can be correct. Select and explain all that apply. 1. R6-512, X=0, R5=24 2. R6-512, X=24, R5=0 3. R6-24, X-512, R5=0 4. R6=24, X=0, R5=512

The variable A is stored at memory address 24. We want to change its value to 512. Which of the following combinations of R5, R6, and the constant X will accomplish this with the instruction sw R6, X(R5)? Briefly explain. Note: more than one answer can be correct. Select and explain all that apply. 1. R6-512, X=0, R5=24 2. R6-512, X=24, R5=0 3. R6-24, X-512, R5=0 4. R6=24, X=0, R5=512

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Write an instruction that stores a half word value from x5 to the memory at address 394 (in decimal). Answer:
Write out how to solve the following code using any addressing mode for (3,3) GPR. a[] is address0x100, y is address 0x300, z is address 0x400, and x is using r0. Write comments besides each line ofcode. Short a[50];Int y,z;for( x=0; x<20; x++){y = a[x + 3];z = y + a[x+10];}
Convert the given code fragment to assembly code fragment, using only instructions of the following types. These instructions are generally discussed in class. Here X,Y,Z are any memory locations; R, R1, R2 are any general registers; L is a label in the code (you can use any names as labels, ex. L, L1, L2 etc. ). load X, R //copy contents of memory location X into R. store R, X //Store contents of R into Mem location X cmp R1, R2 //Compute R1-R2 and update condition codes; //throw away result of subtraction. jmp L //Jump to location L in the code. jmpp L //If P bit is 1, Jump to location L in the code add X, R //Add contents of X,R and store result in R; //Also update the condition codes. Be careful about what type of argument is allowed in the instruction (Memory or Register). Ex. the first argument of ADD instruction is memory, not register. Do Not…
Fill all the information to reflect the addresses of the program memory Adress code, .org 0x540 LDS R10, 0x700 LDI R20, 20 LDI R16, 10 ADD R16, R20 STS 0x700, R16 ADD R16, R10 STS 0x701, R16 Ox540 Ox541 Ox542 Ox543 Ox544| Ox545 0x546|| Ox547 Ox548 0x549 0x54A
Registers in RISC-V are 64-bit. For the sake of simplicity, consider the following instructions operating on 32-bit registers. Assume that registers x5 and x6 hold the values 0xBBBBBBBB and 0x00000000, respectively. What is the value in x6 for the followingslli x6, x5, 6 Using the result from the part above, what is the value in x6 for the following instruction. srli x6, x6, 6
Study the following handwritten (potentially buggy) code (you can assume "..." refers to code that is not shown main: ... LDS R25, x PUSH R25, CALL subroutine1 ; This instruction is at location ex1296 POP RO, ... subroutine1: ; This subroutine is at location OXAB33 ... MOV R25, R8 CALL subroutine2 ... MOV R24, R7 ; result RET subroutine2: ; This subroutine is at location @XAD54. No code is missing from this subroutine ADD R8 R8 PUSH RS RET Assume the return address stored in the stack by the CALL instruction is 3 bytes. What is the value of the Program Counter after the RET instruction in Subroutine 2? (Write your answer in Decimal, write 0 if unknown)
answer with proper explanation and step by step solution. The instruction is to use a "loop" to write the MIPS code for this.
Orthogonality means that an instruction set has a "backup" instruction that can be used instead of any other instruction that does the same thing. It's up to you to prove or disprove what I think.
Write an instruction that loads the value 1093 (in decimal) in x2. Answer:
So each instruction gets its own input data, regardless of how other instructions get theirs. Using a(n): A Multiple data, multiple instruction B Multiple data, multiple instruction C Single data, single instruction D One command, several data
Please Note: Send me only the correct answer. If you don't know the answer then leave it & forward it to others. Don't give me the wrong answer. I'll give an upvote if you give me the correct answer & send as soon as possible.
Q3/ write a program to cout number of one's & zero's in a number stored at 0200:0010, use rotate instruction, store the result in the memory location 0200:0011 and 0200:0012 respectively.